Nissan Altima HL32 Hybrid. Manual - part 450

 

  Index      Nissan     Nissan Altima HL32 Hybrid (2009 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  448  449  450  451   ..

 

 

Nissan Altima HL32 Hybrid. Manual - part 450

 

 

PREPARATION

FAX-5

< PREPARATION >

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000004212405

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tool

INFOID:0000000004212406

Tool number 
(Kent-Moore No.)
Tool name

Description

HT72520000 
(J-25730-A)
Ball joint remover

Removing outer tie-rod

KV38106700
(J-34296)
KV38106800
(J-34297)
Differential side oil seal protector

Installing drive shaft
LH: KV38106700 (J-34296)
RH: KV38106800 (J-34297)

KV40107300
(

)

Boot Band crimping tool

Installing boot bands

KV40107500
(

)

Drive shaft attachment

Removing drive shaft

NT146

NT147

ZZA1229D

ZZA1230D

Tool name

Description

Power tool

Removing nuts and  bolts

PBIC0190E

FAX-6

< ON-VEHICLE MAINTENANCE >

FRONT WHEEL HUB

ON-VEHICLE MAINTENANCE

FRONT WHEEL HUB

Inspection

INFOID:0000000004212407

• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of

wheel bearing.

• Rotate wheel hub and make sure that is no unusual noise or other irregular conditions. If there is any of

irregular conditions, replace wheel hub and bearing assembly

Axial end play

: 0.05 mm (0.002 in) or less

FRONT DRIVE SHAFT

FAX-7

< ON-VEHICLE MAINTENANCE >

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

FRONT DRIVE SHAFT

Inspection

INFOID:0000000004212408

• Check drive shaft mounting point and joint for looseness and other damage.

• Check boot for cracks and other damage.

CAUTION:

Replace entire drive shaft assembly when noise or vibration occur from drive shaft.

FAX-8

< ON-VEHICLE REPAIR >

FRONT WHEEL HUB AND KNUCKLE

ON-VEHICLE REPAIR

FRONT WHEEL HUB AND KNUCKLE

Removal and Installation

INFOID:0000000004212409

REMOVAL

1. Remove wheel and tire. Refer to 

WT-62, "Adjustment"

.

2. Without disassembling the hydraulic lines, remove brake caliper using power tool. Reposition it aside with

wire. Refer to 

BR-30, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

.

NOTE:

Avoid depressing brake pedal while brake caliper is removed.

3. Put alignment marks on disc rotor and wheel hub and bearing

assembly, then remove disc rotor.

4. Remove wheel sensor from steering knuckle. Refer to 

BRC-202, "Removal and Installation"

.

CAUTION:

Do not pull on wheel sensor harness.

5. Remove cotter pin, then remove lock nut from drive shaft using power tool.
6. Remove steering outer tie-rod cotter pin at steering knuckle, then loosen nut using power tool. Refer to

ST-12, "Removal and Installation"

.

1.

Cotter pin

2.

Disc rotor

3.

Wheel hub and bearing assembly

4.

Splash guard

5.

Steering knuckle

Front

AWDIA0634GB

SDIA1480E

 

 

 

 

 

 

 

Content   ..  448  449  450  451   ..