Nissan Altima HL32 Hybrid. Manual - part 332

 

  Index      Nissan     Nissan Altima HL32 Hybrid (2009 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  330  331  332  333   ..

 

 

Nissan Altima HL32 Hybrid. Manual - part 332

 

 

EC-312

< COMPONENT DIAGNOSIS >

[QR25DE]

P0506 ISC SYSTEM

P0506 ISC SYSTEM

Description

INFOID:0000000004211545

The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let

into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is

varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects

the actual engine speed and sends a signal to the ECM.

The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value

memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.

The optimum value stored in the ECM is determined by taking into consideration various engine conditions,

such as during warming up and deceleration.

DTC Logic

INFOID:0000000004211546

DTC DETECTION LOGIC

NOTE:

If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-

ing the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

If the target idle speed is out of the specified value, perform 

EC-16, "IDLE AIR VOLUME LEARNING :

Special Repair Requirement"

, before conducting DTC Confirmation Procedure.

TESTING CONDITION:

• Before performing the following procedure, confirm that battery voltage is more than 11V at idle.

• Always perform the test at a temperature above 

10°C(14°F).

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Activate “INSPECTION MODE 1” (

HBC-104

.) to start engine, and warm up engine to normal operating

temperature.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Activate “INSPECTION MODE 1” (

HBC-104

.) to start engine, and let engine idle for at least 1 minute.

6. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Go to 

EC-312, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000004211547

1.

CHECK INTAKE AIR LEAK

1. Activate “INSPECTION MODE 1” (

HBC-104

) to start.

2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0506

Idle speed control sys-
tem RPM lower than ex-
pected

The idle speed is less than the target idle speed 
by 100 rpm or more.

• Electric throttle control actuator
• Intake air leak

P0506 ISC SYSTEM

EC-313

< COMPONENT DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

YES

>> Discover air leak location and repair.

NO

>> GO TO 2.

2.

REPLACE ECM

1. Replace ECM.

2. Go to 

EC-14, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

.

>> INSPECTION END

EC-314

< COMPONENT DIAGNOSIS >

[QR25DE]

P0507 ISC SYSTEM

P0507 ISC SYSTEM

Description

INFOID:0000000004363297

The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let

into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is

varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects

the actual engine speed and sends a signal to the ECM.

The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value

memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.

The optimum value stored in the ECM is determined by taking into consideration various engine conditions,

such as during warming up and deceleration.

DTC Logic

INFOID:0000000004211549

DTC DETECTION LOGIC

NOTE:

If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-

ing the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

If the target idle speed is out of the specified value, perform 

EC-16, "IDLE AIR VOLUME LEARNING :

Special Repair Requirement"

, before conducting DTC Confirmation Procedure.

TESTING CONDITION:

• Before performing the following procedure, confirm that battery voltage is more than 11V at idle.

• Always perform the test at a temperature above 

10°C(14°F).

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Activate “INSPECTION MODE 1” (

HBC-104

.) to start engine, and warm up engine to normal operating

temperature.

2. Turn ignition switch OFF and wait at least 10 seconds.

3. Turn ignition switch ON.

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Activate “INSPECTION MODE 1” (

HBC-104

.) to start engine, and let engine idle for at least 1 minute.

6. Check 1st trip DTC.
Is 1st trip DTC detected?

YES

>> Go to 

EC-314, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000004211550

1.

CHECK PCV HOSE CONNECTION

Confirm that PCV hose is connected correctly.
Is the inspection result normal?

YES

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P0507

Idle speed control sys-
tem RPM higher than 
expected

The idle speed is more than the target idle 
speed by 200 rpm or more.

• Electric throttle control actuator
• Intake air leak
• PCV system

P0507 ISC SYSTEM

EC-315

< COMPONENT DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Repair or replace.

2.

CHECK INTAKE AIR LEAK

1. Activate “INSPECTION MODE 1” (

HBC-104

) to start engine.

2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?

YES

>> Discover air leak location and repair.

NO

>> GO TO 3.

3.

REPLACE ECM

1. Replace ECM.

2. Go to 

EC-14, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

.

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  330  331  332  333   ..