Nissan Altima HL32 Hybrid. Manual - part 278

 

  Index      Nissan     Nissan Altima HL32 Hybrid (2009 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  276  277  278  279   ..

 

 

Nissan Altima HL32 Hybrid. Manual - part 278

 

 

EC-96

< FUNCTION DIAGNOSIS >

[QR25DE]

ON BOARD DIAGNOSTIC (OBD) SYSTEM

*2: This mode includes 1st trip freeze frame data or freeze frame data. The items appear on CONSULT-III screen in freeze frame data
mode only if a 1st trip DTC or DTC is detected. For details, refer to 

EC-82, "Diagnosis Description"

.

*3: Always “CMPLT” is displayed.

INSPECTION PROCEDURE

Refer to CONSULT-III Operators Manual.

WORK SUPPORT MODE

Work Item

*1: If this function is performed, a certain DTC may be detected.
*2: This function is not necessary in the usual service procedure.

SELF-DIAG RESULTS MODE

Self Diagnostic Item

Regarding items of DTC and 1st trip DTC, refer to 

EC-442, "DTC Index"

.)

Freeze Frame Data and 1st Trip Freeze Frame Data

WORK ITEM

CONDITION

USAGE

FUEL PRESSURE RELEASE*

1

• SELECTOR LEVER IS N POSITION WITH ENGINE RUN-

NING.

• FUEL PUMP WILL STOP BY TOUCHING “START”.

When releasing fuel pressure from 
fuel line

IDLE AIR VOL LEARN

• IGNITION SWITCH ON (READY)
• THE IDLE AIR VOLUME THAT KEEPS THE ENGINE 

WITHIN THE SPECIFIED RANGE IS MEMORIZED IN 
ECM.

When learning the idle air volume

SELF-LEARNING CONT

• THE COEFFICIENT OF SELF-LEARNING CONTROL 

MIXTURE RATIO RETURNS TO THE ORIGINAL COEF-
FICIENT.

When clearing mixture ratio self-
learning value

EVAP SYSTEM CLOSE

CLOSE THE EVAP CANISTER VENT CONTROL VALVE IN 
ORDER TO MAKE EVAP SYSTEM CLOSE UNDER THE 
FOLLOWING CONDITIONS.
• IGN SW ON
• ENGINE NOT RUNNING
• AMBIENT TEMPERATURE IS ABOVE 0

°C (32°F).

• NO VACUUM AND NO HIGH PRESSURE IN EVAP SYS-

TEM

•  FUEL TANK TEMP. IS MORE THAN 0

°C (32°F).

• WITHIN 10 MINUTES AFTER STARTING “EVAP SYS-

TEM CLOSE”

• WHEN TRYING TO EXECUTE “EVAP SYSTEM CLOSE” 

UNDER THE CONDITION EXCEPT ABOVE, CONSULT-
III WILL DISCONTINUE IT AND DISPLAY APPROPRI-
ATE INSTRUCTION.
NOTE:
WHEN STARTING ENGINE, CONSULT-III MAY DIS-
PLAY “BATTERY VOLTAGE IS LOW. CHARGE BAT-
TERY”, EVEN IN USING CHARGED BATTERY.

When detecting EVAP vapor leak 
point of EVAP system

VIN REGISTRATION

• IN THIS MODE, VIN IS REGISTERED IN ECM.

When registering VIN in ECM

TARGET IDLE RPM ADJ*

2

• INSPECTION MODE
• IDLE CONDITION

When setting target idle speed

TARGET IGN TIM ADJ*

2

• INSPECTION MODE
• IDLE CONDITION

When adjusting target ignition tim-
ing

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-97

< FUNCTION DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

*: The items are the same as those of 1st trip freeze frame data.

DATA MONITOR MODE

Monitored Item

×: Applicable

Freeze frame data 

item*

Description

DIAG TROUBLE 
CODE
[PXXXX]

• The engine control component part/control system has a trouble code, it is displayed as PXXXX. (Refer to 

EC-442, "DTC Index"

.)

FUEL SYS-B1

• “Fuel injection system status” at the moment a malfunction is detected is displayed.
• One mode in the following is displayed.

Mode2: Open loop due to detected system malfunction
Mode3: Open loop due to driving conditions (power enrichment, deceleration enleanment)
Mode4: Closed loop - using oxygen sensor(s) as feedback for fuel control
Mode5: Open loop - has not yet satisfied condition to go to closed loop

CAL/LD VALUE [%]

• The calculated load value at the moment a malfunction is detected is displayed.

COOLANT TEMP [

°C] 

or [

°F]

• The engine coolant temperature at the moment a malfunction is detected is displayed.

L-FUEL TRM-B1 [%]

• “Long-term fuel trim” at the moment a malfunction is detected is displayed.
• The long-term fuel trim indicates much more gradual feedback compensation to the base fuel schedule than 

short-term fuel trim.

S-FUEL TRM-B1 [%]

• “Short-term fuel trim” at the moment a malfunction is detected is displayed.
• The short-term fuel trim indicates dynamic or instantaneous feedback compensation to the base fuel sched-

ule.

ENGINE SPEED [rpm] • The engine speed at the moment a malfunction is detected is displayed.

VEHICL SPEED
[km/h] or [mph]

• The vehicle speed at the moment a malfunction is detected is displayed.

ABSOL TH·P/S [%]

• The throttle valve opening angle at the moment a malfunction is detected is displayed.

B/FUEL SCHDL 
[msec]

• The base fuel schedule at the moment a malfunction is detected is displayed.

INT/A TEMP SE [

°C] 

or [

°F]

• The intake air temperature at the moment a malfunction is detected is displayed.

FUEL SYS-B2

• These items displayed but are not applicable to this model.

L-FUEL TRM-B2 [%]

S-FUEL TRM-B2 [%]

INT MANI PRES [kPa] 

COMBUST CONDI-
TION

Monitored item

Unit

Description

Remarks

ENG SPEED

rpm

• Indicates the engine speed computed from the 

signal of the crankshaft position sensor (POS) 
and camshaft position sensor (PHASE).

• Accuracy becomes poor if engine 

speed drops below the idle rpm.

• If the signal is interrupted while the 

engine is running, an abnormal value 
may be indicated.

MAS A/F SE-B1

V

• The signal voltage of the mass air flow sensor is 

displayed.

• When the engine is stopped, a certain 

value is indicated.

• When engine is running specification 

range is indicated in “SPEC”.

B/FUEL SCHDL

ms

• “Base fuel schedule” indicates the fuel injection 

pulse width programmed into ECM, prior to any 
learned on board correction.

• When engine is running specification 

range is indicated in “SPEC”.

EC-98

< FUNCTION DIAGNOSIS >

[QR25DE]

ON BOARD DIAGNOSTIC (OBD) SYSTEM

A/F ALPHA-B1

%

• The mean value of the air-fuel ratio feedback cor-

rection factor per cycle is indicated.

• When the engine is stopped, a certain 

value is indicated.

• When engine is running specification 

range is indicated in “SPEC”.

• This data also includes the data for 

the air-fuel ratio learning control.

COOLAN TEMP/S

°C or °F

• The engine coolant temperature (determined by 

the signal voltage of the engine coolant tempera-
ture sensor) is displayed.

• When the engine coolant temperature 

sensor is open or short-circuited, 
ECM enters fail-safe mode. The en-
gine coolant temperature determined 
by the ECM is displayed.

A/F SEN1 (B1)

V

• The A/F signal computed from the input signal of 

the air fuel ratio (A/F) sensor 1 is displayed.

HO2S2 (B1)

V

• The signal voltage of the heated oxygen sensor 2 

is displayed.

HO2S3(B1)

V

• The signal voltage of the heated oxygen sensor 3 

is displayed.

HO2S2 MNTR(B1)

RICH/LEAN

• Display of heated oxygen sensor 2 signal:

RICH: means the amount of oxygen after three 
way catalyst is relatively small.
LEAN: means the amount of oxygen after three 
way catalyst is relatively large.

• When the engine is stopped, a certain 

value is indicated.

VHCL SPEED SE

km/h or mph

• The vehicle speed computed from the vehicle 

speed signal sent from brake ECU is displayed.

BATTERY VOLT

V

• The power supply voltage of ECM is displayed.

TP SEN 1-B1

V

• The throttle position sensor signal voltage is dis-

played.

• TP SEN 2-B1 signal is converted by 

ECM internally. Thus, it differs from 
ECM terminal voltage signal.

TP SEN 2-B1

FUEL T/TMP SE

°C or °F

• The fuel temperature (determined by the signal 

voltage of the fuel tank temperature sensor) is 
displayed.

INT/A TEMP SE

°C or °F

• The intake air temperature (determined by the 

signal voltage of the intake air temperature sen-
sor) is indicated.

EVAP SYS PRES

V

• The signal voltage of EVAP control system pres-

sure sensor is displayed.

FUEL LEVEL SE

V

• The signal voltage of the fuel level sensor is dis-

played.

START SIGNAL

ON/OFF

• Indicates start signal status [ON/OFF] computed 

by the ECM according to the input signals.

• After starting the engine, [OFF] is dis-

played regardless of the starter sig-
nal.

CLSD THL POS

ON/OFF

• Indicates idle position [ON/OFF] computed by 

ECM according to the engine power request sig-
nal.

AIR COND SIG

ON/OFF

• Indicates [ON/OFF] condition of the air condition-

er switch as determined by the air conditioner sig-
nal.

P/N POSI SW

ON/OFF

• Indicates [ON/OFF] condition from the park/neu-

tral position (PNP) switch signal.

PW/ST SIGNAL

ON/OFF

• Always OFF is displayed.
• This item is not efficient for L32 models.

LOAD SIGNAL

ON/OFF

• Indicates [ON/OFF] condition from the electrical 

load signal.
ON: Rear window defogger switch is ON and/or 
lighting switch is in 2nd position.
OFF: Both rear window defogger switch and light-
ing switch are OFF.

Monitored item

Unit

Description

Remarks

ON BOARD DIAGNOSTIC (OBD) SYSTEM

EC-99

< FUNCTION DIAGNOSIS >

[QR25DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

IGNITION SW

ON/OFF

• Indicates [ON/OFF] condition from ignition switch 

signal.

HEATER FAN SW

ON/OFF

• Indicates [ON/OFF] condition from the blower fan 

switch signal.

BRAKE SW

ON/OFF

• Indicates [ON/OFF] condition from the stop lamp 

switch signal.

INJ PULSE-B1

msec

• Indicates the actual fuel injection pulse width 

compensated by ECM according to the input sig-
nals.

• When the engine is stopped, a certain 

computed value is indicated.

IGN TIMING

BTDC

• Indicates the ignition timing computed by ECM 

according to the input signals.

• When the engine is stopped, a certain 

value is indicated.

CAL/LD VALUE

%

• “Calculated load value” indicates the value of the 

current air flow divided by peak air flow.

MASS AIRFLOW

g·m/s

• Indicates the mass air flow computed by ECM ac-

cording to the signal voltage of the mass air flow 
sensor.

PURG VOL C/V

%

• Indicates the EVAP canister purge volume con-

trol solenoid valve control value computed by the 
ECM according to the input signals.

• The opening becomes larger as the value in-

creases.

INT/V TIM(B1)

°CA

• Indicates [

°CA] of intake camshaft advance an-

gle. 

INT/V SOL(B1)

%

• The control value of the intake valve timing con-

trol solenoid valve (determined by ECM accord-
ing to the input signals) is indicated.

• The advance angle becomes larger as the value 

increases.

FUEL PUMP RLY

ON/OFF

• Indicates the fuel pump relay control condition 

determined by ECM according to the input sig-
nals.

VENT CONT/V

ON/OFF

• The control condition of the EVAP canister vent 

control valve (determined by ECM according to 
the input signals) is indicated.
ON: Closed
OFF: Open

THRTL RELAY

ON/OFF

• Indicates the throttle control motor relay control 

condition determined by the ECM according to 
the input signals.

HO2S2 HTR (B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen 

sensor 2 heater determined by ECM according to 
the input signals.

HO2S3 HTR(B1)

ON/OFF

• Indicates [ON/OFF] condition of heated oxygen 

sensor 3 heater determined by ECM according to 
the input signals.

VEHICLE SPEED

km/h or mph

• The vehicle speed computed from the vehicle 

speed signal sent from HV ECU is displayed.

IDL A/V LEARN

YET/CMPLT

• Display the condition of Idle Air Volume Learning

YET: Idle air volume learning has not been per-
formed yet.
CMPLT: Idle air volume learning has already 
been performed successfully.

TRVL AFTER MIL

km or mile

• Distance traveled while MIL is activated.

A/F S1 HTR(B1)

%

• Air fuel ratio (A/F) sensor 1 heater control value 

computed by ECM according to the input signals.

• The current flow to the heater becomes larger as 

the value increases.

Monitored item

Unit

Description

Remarks

 

 

 

 

 

 

 

Content   ..  276  277  278  279   ..