Nissan Altima HL32 Hybrid. Manual - part 1113

C1712 - C1715, C1720 - C1723, C1724 - C1727 TRANSMITTER MALFUNCTION

WT-17

< COMPONENT DIAGNOSIS >

DRIVE VEHICLE

1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for

10 minutes.

2. Check all tire pressures with CONSULT-III within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?

YES

>> Inspection End.

>> Replace malfunctioning transmitter, and perform Step 3 again.

Special Repair Requirement

INFOID:0000000004212501

Perform preliminary check. Refer to

WT-5, "Preliminary Check"

WT-18

< COMPONENT DIAGNOSIS >

C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION

C1716 - C1719 TRANSMITTER PRESSURE MALFUNCTION

Description

INFOID:0000000004212502

Air pressure data from one or more transmitters is out of range.

DTC Logic

INFOID:0000000004212503

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

ID REGISTRATION AND VEHICLE DRIVING

1. Carry out ID registration of all transmitters.

2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for

10 minutes.

3. Check all tire pressures with CONSULT-III within 5 minutes.
Does DATA MONITOR ITEM display tire pressure as normal without any warning lamp?

YES

>> Inspection End.

>> Refer to

WT-18, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000004212504

MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)

CHECK ALL TIRE PRESSURES

Check all tire pressures. Refer to

WT-66, "Tire"

Are there any tires with pressure of 64 psi or more?

YES

>> Adjust tire pressure to specified value.

>> GO TO 2

ID REGISTRATION AND VEHICLE DRIVING

1. Carry out ID registration of all transmitters. Refer to

WT-6, "ID Registration Procedure"

2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11

MPH).

Does “DATA MONITOR ITEM” display 64 psi or more?

YES

>> Replace transmitter. Refer to

WT-64, "Removal and Installation"

. GO TO 3.

>> GO TO 3

ID REGISTRATION AND VEHICLE DRIVING

1. Carry out ID registration of all transmitters.

2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for

10 minutes.

3. Check all tire pressures with CONSULT-III within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp?

YES

>> Inspection End.

>> Proceed to the inspection applicable to DTC.

Special Repair Requirement

INFOID:0000000004212505

Perform preliminary check. Refer to

WT-5, "Preliminary Check"

DTC

CONSULT - III

DTC detecting condition

C1716

[PRESSDATA - ERR] FL

Air pressure data from FL transmitter is malfunctioning.

C1717

[PRESSDATA - ERR] FR

Air pressure data from FR transmitter is malfunctioning.

C1718

[PRESSDATA - ERR] RR

Air pressure data from RR transmitter is malfunctioning.

C1719

[PRESSDATA - ERR] RL

Air pressure data from RL transmitter is malfunctioning.

C1729 VEHICLE SPEED SIGNAL

WT-19

< COMPONENT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000004212506

The vehicle speed signal is not being detected by the BCM.

DTC Logic

INFOID:0000000004212507

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSTIC RESULTS

1. On SELECT DIAG MODE, select the SELF-DIAG RESULT screen.

2. Check display contents on SELF DIAG RESULT screen.
Is the CAN COMM CIRCUIT displayed in the self-diagnosis display?

YES

>> Refer to

WT-19, "Diagnosis Procedure"

>> Inspection end.

Diagnosis Procedure

INFOID:0000000004212508

MALFUNCTION CODE NO. 52 (DTC C1729)

CHECK SELF-DIAGNOSTIC RESULTS

1. On “SELECT DIAG MODE”, select the “SELF-DIAG RESULT” screen.

2. Check display contents on "SELF DIAG RESULT" screen.
Is the “CAN COMM CIRCUIT” displayed in the self-diagnosis display?

YES

>> Perform trouble diagnosis for CAN communication system. Refer to

LAN-16, "Trouble Diagnosis

Flow Chart"

>> Check combination meter. Refer to

MWI-35, "CONSULT-III Function (METER/M&A)"

Special Repair Requirement

INFOID:0000000004212509

Perform preliminary check. Refer to

WT-5, "Preliminary Check"

DTC

CONSULT - III

DTC detecting condition

C1729

VHCL SPEED SIG ERR

Vehicle speed signal is in error.

WT-20

< COMPONENT DIAGNOSIS >

C1734 CONTROL UNIT

C1734 CONTROL UNIT

Description

INFOID:0000000004212510

An internal malfunction has been detected in the TPMS function of the BCM.

DTC Logic

INFOID:0000000004212511

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSTIC RESULTS

1. On SELECT DIAG MODE, select the SELF-DIAG RESULT screen.

2. Check display contents on SELF DIAG RESULT screen.
Is C1734 displayed in the self-diagnosis display?

YES

>> Refer to

WT-20, "Diagnosis Procedure"

>> Inspection End.

Diagnosis Procedure

INFOID:0000000004212512

MALFUNCTION CODE NO. 53 (DTC C1734)

SELF-DIAGNOSTIC RESULTS

1. On “SELECT DIAG” mode, select the “SELF-DIAG RESULT” screen for BCM.

2. Check display contents on "SELF-DIAG RESULT".
Does self-diagnostic results indicate any DTC other than C1734?

YES

>> Perform trouble diagnosis for DTC. Refer to

BCS-81, "DTC Index"

>> GO TO 2.

CHECK BCM HARNESS CONNECTORS

Check BCM harness connectors for damage or loose connections.
Are the BCM harness connectors damaged or loose?

YES

>> Repair or replace damaged parts.

>> GO TO 3.

BCM POWER SUPPLY AND GROUND

Check BCM power supply and ground. Refer to

BCS-42, "Diagnosis Procedure"

Are the power supply and grounds normal?

YES

>> GO TO 4.

>> Repair power supply or grounds as necessary.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

1. Turn ignition switch “OFF”

2. Disconnect BCM harness connector M18 (A) and tire pressure

receiver harness connector M70 (B).

3. Check continuity between BCM harness connector and tire

pressure receiver harness connector.

DTC

CONSULT - III

DTC detecting condition

C1734

CONTROL UNIT

TPMS malfunction in BCM.

ALEIA0013ZZ

Content .. 1111 1112 1113 1114 ..