Nissan Sentra. Manual - part 931

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Repair or replace malfunctioning components.

AIR PRESS RR

Approximately equal to value indicated on tire gauge for rear RH tire

AIR PRESS RL

Approximately equal to value indicated on tire gauge for rear LH tire

Monitor item

Displayed value

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

DTC Logic

INFOID:0000000009758147

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II

User Guide for additional information.

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PERFORM SELF DIAGNOSTIC RESULT 

With CONSULT

1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2. Stop the vehicle.

3. Perform “SELF DIAGNOSTIC RESULT”.
Is DTC “C1708”, “C1709”, “C1710” or “C1711” detected?

YES

>> Proceed to 

WT-27, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009758148

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II

User Guide for additional information.

• Activate and display TPMS transmitter IDs

• Display tire pressure reported by the TPMS transmitter

• Read TPMS DTCs

• Register TPMS transmitter IDs

Regarding Wiring Diagram information, refer to 

WT-15, "WITH INTELLIGENT KEY : Wiring Diagram"

 or 

WT-

18, "WITHOUT INTELLIGENT KEY : Wiring Diagram"

.

1.

CHECK DATA MONITOR

With CONSULT

1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2. Stop the vehicle.

3. On “DATA MONITOR” select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.

4. Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.
Are all tire pressures displayed 0 kPa (psi)?

YES

>> GO TO 2.

NO

>> GO TO 5.

DTC

Display Item

Malfunction detected condition

Possible causes

C1708

[NO DATA] FL

Tire pressure data signal from the front LH wheel 
transmitter cannot be detected.

• Harness or connector connec-

tion malfunction

• Transmitter ID registration in-

complete

• Transmitter malfunction

C1709

[NO DATA] FR

Tire pressure data signal from the front RH wheel 
transmitter cannot be detected.

C1710

[NO DATA] RR

Tire pressure data signal from the rear RH wheel 
transmitter cannot be detected.

C1711

[NO DATA] RL

Tire pressure data signal from the rear LH wheel 
transmitter cannot be detected.

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

2.

CHECK REMOTE KEYLESS ENTRY RECEIVER POWER CIRCUIT

Check voltage between remote keyless entry receiver connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connectors.

3.

CHECK REMOTE KEYLESS ENTRY RECEIVER SIGNAL CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect BCM and remote keyless entry receiver connectors.

3. Check continuity between BCM and remote keyless entry receiver connectors.

4. Check continuity between BCM connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning harness or connector.

4.

CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT

Check continuity between BCM and remote keyless entry receiver connectors.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning harness or connector.

5.

TRANSMITTER ID REGISTRATION

Perform transmitter ID registration. Refer to 

WT-22, "Work Procedure"

.

Can the tire pressure sensor ID registration be completed?

YES

>> GO TO 6.

NO

>> Replace applicable transmitter. Refer to 

WT-50, "Removal and Installation"

.

6.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

1. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

2. Stop the vehicle.

3. On “DATA MONITOR” select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.

Remote keyless entry receiver

Ground

Voltage

(Approx.)

Connector

Terminal

M91 (with Intelligent Key system)

1

—

5V

M131 (without Intelligent Key system)

4

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M84 (with Intelligent Key system)

38

M91 (with Intelligent Key system)

2

Yes

M21 (without Intelligent Key system)

20

M131 (without Intelligent Key system)

BCM

—

Continuity

Connector

Terminal

M84 (with Intelligent Key system)

38

Ground

No

M21 (without Intelligent Key system)

20

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M84 (with Intelligent Key system)

18

M91 (with Intelligent Key system)

4

Yes

M21 (without Intelligent Key system)

M131 (without Intelligent Key system)

1

C1708, C1709, C1710, C1711 TRANSMITTER (NO DATA)

WT-29

< DTC/CIRCUIT DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

4. Within 5 minutes after vehicle stopped, check that the tire pressures are within specification. Refer to 

WT-

54, "Tire Air Pressure"

.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace the BCM. Refer to 

BCS-73, "Removal and Installation"

 (with Intelligent Key system) or

BCS-126, "Removal and Installation"

 (without Intelligent Key system).

Monitor item

Displayed value

AIR PRESS FL

Approximately equal to the indication on tire gauge value for front LH tire

AIR PRESS FR

Approximately equal to the indication on tire gauge value for front RH tire

AIR PRESS RR

Approximately equal to the indication on tire gauge value for rear RH tire

AIR PRESS RL

Approximately equal to the indication on tire gauge value for rear LH tire