Nissan Leaf. Manual - part 257

 

  Index      Nissan     Nissan Leaf (2011-2014 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  255  256  257  258   ..

 

 

Nissan Leaf. Manual - part 257

 

 

C1AA1 STROKE SENSOR

BR-349

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

4. Repeat step 3 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

5. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

6. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

7. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

8. Start CONSULT and erase self-diagnosis result of “BRAKE”.

9. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

10. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

11. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

12. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

13. Release brake pedal.

14. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AA1” detected?

YES

>> GO TO 22.

NO

>> INSPECTION END

BR-350

< DTC/CIRCUIT DIAGNOSIS >

C1AA2 STROKE SENSOR

C1AA2 STROKE SENSOR

DTC Logic

INFOID:0000000010123071

DTC DETECTION LOGIC

DTC REPRODUCTION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn power switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

2. Repeat step 1 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

6. Start CONSULT and erase self-diagnosis result of “BRAKE”.

7. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

8. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

11. Release brake pedal.

12. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AA2” detected?

YES

>> Proceed to 

BR-350, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010123072

1.

CHECK 12V BATTERY

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

DTC

Display item

Malfunction detection condition

Possible causes

C1AA2

STROKE SENSOR-4

An internal malfunction is detected in the stroke sen-
sor. (Without fluctuations in output voltage of the 
stroke sensor)

• Harness or connector
• Stroke sensor
• Electrically-driven intelligent 

brake unit

C1AA2 STROKE SENSOR

BR-351

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

BR

N

O

P

Never operate the vehicle while waiting.

3. Check the 12V battery terminal connections. Refer to 

BR-6, "Precaution for Removing 12V Battery"

 and

PG-83, "Work Flow"

.

4. Check the 12V battery. Refer to 

PG-83, "Work Flow"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts and GO TO 2.

2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

1. Connect 12V battery cable to negative terminal.

2. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

3. Repeat step 2 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

4. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

5. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

6. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

7. Start CONSULT and erase self-diagnosis result of “BRAKE”.

8. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

9. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

10. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

11. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

12. Release brake pedal.

13. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AA2” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK CONNECTOR TERMINALS

1. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

2. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

3. Disconnect 12V battery cable from negative terminal. Refer to 

BR-6, "Precaution for Removing 12V Bat-

tery"

.

4. Disconnect the electrically-driven intelligent brake unit harness connector, then check for failures of pin

terminals and connections.

5. Disconnect the stroke sensor harness connector, then check for failures of pin terminals and connections.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts and GO TO 4.

4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

1. Connect the electrically-driven intelligent brake unit harness connector.

BR-352

< DTC/CIRCUIT DIAGNOSIS >

C1AA2 STROKE SENSOR

2. Connect stroke sensor harness connector.

3. Connect 12V battery cable to negative terminal.

4. Turn the power switch OFF to ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

5. Repeat step 4 two or more times.

CAUTION:

Be sure to wait for 5 seconds or more after turning the power switch OFF.

6. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

7. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

8. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

9. Start CONSULT and erase self-diagnosis result of “BRAKE”.

10. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

11. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

12. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

13. Depress brake pedal by 100 mm (3.94 in) or more, and hold the position for 5 seconds or more.

14. Release brake pedal.

15. Start CONSULT and perform “BRAKE” self-diagnosis.
Is DTC “C1AA2” detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

CHECK POWER SWITCH ON POWER SUPPLY 

1. Connect stroke sensor harness connector.

2. Connect 12V battery cable to negative terminal.

3. Turn the power switch OFF to exit CONSULT, and disconnect CONSULT from data link connector.

4. Close all doors (including back door), check that the room lamp is OFF, get out of the vehicle, and wait for

3 minutes or more with all doors closed.

CAUTION:

Never operate the vehicle while waiting.

5. Disconnect 12V battery cable from negative terminal. Refer to 

BR-6, "Precaution for Removing 12V Bat-

tery"

.

6. Disconnect the electrically-driven intelligent brake unit harness connector.

7. Connect 12V battery cable to negative terminal.

8. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

9. Turn the power switch ON without depressing the brake pedal.

CAUTION:

Never set the vehicle to READY.

10. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

Electrically-driven intelligent brake unit

Voltage

(Approx.)

Connector

Terminal

E34

26

Ground

0 V

Electrically-driven intelligent brake unit

Voltage

(Approx.)

Connector

Terminal

E34

26

Ground

10 

− 16 V

 

 

 

 

 

 

 

Content   ..  255  256  257  258   ..