Nissan Frontier D22. Manual - part 897

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..

 

 

Nissan Frontier D22. Manual - part 897

 

 

SB-8

COLLISION DIAGNOSIS

COLLISION DIAGNOSIS

PFP:00015

Seat Belt Inspection

EHS000SM

AFTER A COLLISION

WARNING:

Inspect all seat belt assemblies including retractors and attaching hardware after any collision.
NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the col-
lision was minor and the belts show no damage and continue to operate properly. Failure to do so
could result in serious personal injury in an accident. Seat belt assemblies not in use during a colli-
sion should also be replaced if either damage or improper operation is noted. Seat belt assemblies
which are equipped with pre-tensioners should be replaced even if the seat belts are not in use during
a frontal collision in which the air bags are deployed.

Replace any seat belt assembly (including anchor bolts) if:

The seat belt was in use at the time of a collision (except after minor collisions when the belts, retractors
and buckles show no damage and continue to operate properly.)

The seat belt was damaged in an accident (i.e. torn webbing, bent retractor or guide, etc.).

The seat belt attaching point was damaged in an accident. Inspect the seat belt attaching area for damage
or distortion and repair as necessary before installing a new seat belt assembly.

The seat belt assembly is equipped with a pre-tensioner, even if the seat belt is not in use during a colli-
sion in which the air bags are deployed.

PRELIMINARY CHECKS

1.

Check the seat belt warning lamp/chime for proper operation as follows:

a.

Switch ignition ON. With driver seat belt unfastened, the seat belt warning lamp should illuminate. Also,
the seat belt warning chime should sound for about seven seconds.

b.

Fasten driver seat belt. The seat belt warning lamp should go out and the chime (if sounding) should stop.

2.

If the “AIR BAG” warning lamp is blinking, conduct self-diagnosis using CONSULT-II and “AIR BAG” warn-
ing lamp. Refer to 

SRS-20, "SRS Operation Check"

 .

3.

Check that the seat belt retractor, seat belt anchor and buckle bolts are securely attached.

4.

Check the shoulder seat belt guide and shoulder belt height adjuster for front seats. Ensure guide swivels
freely and that belt lays flat and does not bind in guide. Ensure height adjuster operates properly and
holds securely.

5.

Check retractor operation:

a.

Fully extend the seat belt webbing and check for twists, tears or other damage.

b.

Allow the seat belt to retract. Ensure that belt returns smoothly and completely into the retractor.
If the seat belt does not return smoothly, wipe the inside of the
loops with a clean paper cloth etc. Dirt built up in the loops of the
upper anchors can cause the seat belts to retract slowly.

c.

Fasten the seat belt. Pull firmly on belt and buckle to ensure belt
remains latched. Unfasten seat belt. Ensure belt releases freely
and buckle button returns to original position.

6.

For non-retractable seat belts, check that the seat belts are
accessible. Check seat belt webbing for twists, tears or other
damage. Fasten the seat belt. Pull firmly on belt and buckle to
ensure belt remains latched. Unfasten seat belts. Ensure belt
releases freely and buckle button returns to original position.

7.

Repeat steps above as necessary to check the other seat belts.

ARS340

COLLISION DIAGNOSIS

SB-9

C

D

E

F

G

I

J

K

L

M

A

B

SB

SEAT BELT RETRACTOR ON-VEHICLE CHECK
Emergency Locking Retractors (ELR) and Automatic Locking Retractors (ALR)

NOTE:
All seat belt retractors are of the Emergency Locking (ELR) type. In an emergency (sudden stop) the retractor
will lock and prevent the belt from extending any further. All outboard 3-point type seat belt retractors except
the driver seat belt also have an Automatic Locking (ALR) mode. The ALR mode (also called child restraint
mode) is used when installing child seats in outboard seating positions. The ALR mode is activated when the
seat belt is fully extended. When the belt is then retracted partially, the ALR mode automatically locks the seat
belt in a specific position so the belt cannot be extended any further. To cancel the ALR mode, allow the seat
belt to fully wind back into the retractor.
Check the seat belt retractors using the following test(s) to determine if a retractor assembly is operating prop-
erly.

ELR Function Stationary Check

Grasp the shoulder belt and pull forward quickly. The retractor should lock and prevent the belt from extending
further.

ALR Function Stationary Check

1.

Pull out entire length of seat belt from retractor until a click is heard.

2.

Retract the belt partially. A clicking noise should be heard as the belt retracts, indicating that the retractor
is in the Automatic Locking (ALR) mode.

3.

Grasp the seat belt and try to pull out of retractor. The belt must lock and not extend any further. If NG,
replace the retractor assembly.

4.

Allow the entire length of the belt to retract to cancel the automatic locking mode.

ELR Function Moving Check (all outboard seating positions)

WARNING:

Perform the following test in a safe, open area clear of other vehicles and obstructions (for example, a
large, empty parking lot). Road surface must be paved and dry. DO NOT perform the following test on
wet roads, gravel roads, public streets or highways. This could result in an accident and serious per-
sonal injury. The driver and passenger must be prepared to brace themselves in the event the retractor
does not lock.

1.

Fasten driver seat belt. Buckle a passenger into the seat for the belt that is to be tested.

2.

Proceed to the designated safe area.

3.

Drive the vehicle at approximately 16 km/h (10 mph). Notify any passengers of a pending sudden stop
and the driver and passenger must be prepared to brace themselves in the event the retractor does not
lock. Apply brakes firmly and make a very hard stop.

4.

During stop, seat belts should lock and not extend. If the seat belt retractor assembly does not lock, per-
form the seat belt retractor off-vehicle check. Refer to 

SB-10, "SEAT BELT RETRACTOR OFF-VEHICLE

CHECK"

 .

SB-10

COLLISION DIAGNOSIS

SEAT BELT RETRACTOR OFF-VEHICLE CHECK

1.

Remove the seat belt retractor assembly.

2.

Slowly pull out belt while tilting the retractor assembly forward from the mounted position as shown in the
illustration.

3.

If NG, replace the retractor assembly.

15 degrees or less tilt

: Belt can be pulled out.

35 degrees or more tilt

: Belt locks and cannot be pulled out.

LRS199

TOP TETHER STRAP CHILD RESTRAINT

SB-11

C

D

E

F

G

I

J

K

L

M

A

B

SB

TOP TETHER STRAP CHILD RESTRAINT

PFP:88000

Removal and Installation

EHS000SN

KING CAB MODELS

CAUTION:

Replace anchor bolts if they are deformed or worn out.

CREW CAB MODELS

CAUTION:

Replace anchor bolts if they are deformed or worn out.

WRS226

WRS227

 

 

 

 

 

 

 

Content   ..  895  896  897  898   ..