Nissan Frontier D22. Manual - part 405

 

  Index      Nissan     Nissan Frontier D22 Pickup (1998-2004 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  403  404  405  406   ..

 

 

Nissan Frontier D22. Manual - part 405

 

 

DTC P0101 MAF SENSOR

EC-723

[VG33E]

C

D

E

F

G

H

I

J

K

L

M

A

EC

Wiring Diagram

UBS00DG7

BBWA0470E

EC-724

[VG33E]

DTC P0101 MAF SENSOR

Specification data are reference values and are measured between each terminal and ground.

CAUTION:

Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than the ECM terminals, such as the ground.

Diagnostic Procedure

UBS00DG8

1. 

INSPECTION START

Which malfunction (A or B) is duplicated?

A or B

A

>> GO TO 3.

B

>> GO TO 2.

2. 

CHECK INTAKE SYSTEM

Check the following for connection.

Air duct

Vacuum hoses

Intake air passage between air duct to intake manifold collector

OK or NG

OK

>> GO TO 3.

NG

>> Reconnect the parts.

3. 

RETIGHTEN GROUND SCREWS

1.

Turn ignition switch OFF.

2.

Loosen and retighten engine ground screws.

>> GO TO 4.

TER-

MINAL 

NO.

WIRE 

COLOR

ITEM

CONDITION

DATA (DC Voltage)

54

R

Mass air flow sensor

[Engine is running]

Warm-up condition

Idle speed

1.0 - 1.7V 

[Engine is running]

Warm-up condition

Engine speed is 2,500 rpm

1.7 - 2.3V

55

G

Mass air flow sensor 
ground

[Engine is running]

Warm-up condition

Idle speed

Approximately 0V

67

B/P

Power supply for ECM

[Ignition: switch: ON]

BATTERY VOLTAGE
(11 - 14V)

72

B/P

Power supply for ECM

[Ignition: switch: ON]

BATTERY VOLTAGE
(11 - 14V)

BBIA0418E

DTC P0101 MAF SENSOR

EC-725

[VG33E]

C

D

E

F

G

H

I

J

K

L

M

A

EC

4. 

CHECK MAF SENSOR POWER SUPPLY CIRCUIT

1.

Disconnect mass air flow (MAF) sensor harness connector.

2.

Turn ignition switch ON.

3.

Check voltage between terminal 2 and ground with CONSULT-II
or tester.

OK or NG

OK

>> GO TO 6.

NG

>> GO TO 5.

5. 

DETECT MALFUNCTIONING PART

Check the following.

Harness for open or short between ECM relay and mass air flow sensor

Harness for open or short between mass air flow sensor and ECM

>> Repair harness or connectors.

6. 

CHECK MAF SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

1.

Turn ignition switch OFF.

2.

Disconnect ECM harness connector.

3.

Check harness continuity between MAF sensor terminal 3 and ECM terminal 55.
Refer to Wiring Diagram.

4.

Also check harness for short to power.

OK or NG

OK

>> GO TO 7.

NG

>> Repair open circuit or short to ground or short to power in harness or connectors.

7. 

CHECK MAF SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Check harness continuity between MAF sensor terminal 4 and ECM terminal 54.
Refer to Wiring Diagram.

2.

Also check harness for short to ground and short to power.

OK or NG

OK

>> GO TO 8.

NG

>> Repair open circuit or short to ground or short to power in harness or connectors.

AEC641A

Voltage: Battery voltage

SEF627W

Continuity should exist.

Continuity should exist.

EC-726

[VG33E]

DTC P0101 MAF SENSOR

8. 

CHECK MASS AIR FLOW SENSOR

Refer to 

EC-726, "Component Inspection"

 .

OK or NG

OK

>> GO TO 9.

NG

>> Replace mass air flow sensor.

9. 

CHECK INTERMITTENT INCIDENT

Refer to 

EC-696, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"

 .

>> INSPECTION END.

Component Inspection

UBS00DG9

MASS AIR FLOW SENSOR

1.

Reconnect harness connectors disconnected.

2.

Start engine and warm it up to normal operating temperature.

3.

Check voltage between ECM terminal 54 (Mass air flow sensor
signal) and ground.

*: Check for linear voltage rise in response to increases to about 4,000 rpm in
engine speed.

4.

If the voltage is out of specification, proceed the following.

Turn ignition switch OFF.

Disconnect mass air flow sensor harness connector and reconnect it again.

Perform step 2 and 3 again.

5.

If NG, remove mass air flow sensor from air duct. Check hot wire for damage or dust.

6.

If NG, clean or replace mass air flow sensor.

Condition

Voltage V

Ignition switch ON (Engine stopped.)

Less than 1.0

Idle (Engine is warmed-up to normal operating 
temperature.)

1.0 - 1.7

2,500 rpm (Engine is warmed-up to normal oper-
ating temperature.)

1.7 - 2.3

Idle to about 4,000 rpm*

1.0 - 1.7 to Approx. 4.0

SEF747U

 

 

 

 

 

 

 

Content   ..  403  404  405  406   ..