Nissan March K13. Manual - part 624

B1052 DRIVER AIRBAG MODULE

SRC-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1052 DRIVER AIRBAG MODULE

Description

INFOID:0000000005987900

In case of frontal collision where acceleration is more than the specified level, the ignition materials are ignited
by electric ignition system. The system burns the gas generating materials resulting in a chemical reaction.
This generates hot gases that flow into the air bag through a filter and expand the bag.

DTC Logic

INFOID:0000000005987901

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-7, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-35, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005987902

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK SPIRAL CABLE CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect driver air bag module connector and combination switch (spiral cable) connector.

3.

Check continuity between driver air bag module harness connector and combination switch (spiral cable)
harness connector.

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1052
B1057

DRIVER AIRBAG 
MODULE 
[SHORT]

Driver air bag module circuit are shorted to each 
other
(including the spiral cable)

• Disconnection of wiring harness and short
• Malfunction in driver air bag module
• Malfunction in spiral cable
• Malfunction in air bag diagnosis sensor unit

SRC-36

< DTC/CIRCUIT DIAGNOSIS >

B1052 DRIVER AIRBAG MODULE

4.

Check continuity between driver air bag module harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace combination switch (spiral cable). Refer to 

SR-16, "Removal and Installation"

.

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-35, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 5.

NO

>> INSPECTION END

5.

REPLACE DRIVER AIR BAG MODULE

1.

Replace driver air bag module. Refer to 

SR-13, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-35, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

Driver air bag module

Combination switch (spiral cable)

Continuity 

Connector

Terminal

Connector

Terminal

M350

10

M32

28

Existed

11

30

Driver side air bag module

Ground

Continuity 

Connector

Terminal

M350

10

Not existed

11

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

SRC-37

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000006055199

• It detects a shock that is more than the specified level and monitors whether the driver air bag operates nor-

mally. 

• It contains the “G” sensor for frontal collisions and spare battery function in case of main battery damage in

collision.

DTC Logic

INFOID:0000000005987904

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-7, "On Board Diagnosis Function"

.

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-37, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005987905

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes

or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-29, "Removal and Installation"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-37, "DTC Logic"

.

DTC

Display contents of 

CONSULT-III

DTC detecting condition

Possible cause

B1058
B1059
B1060
B1061
B1062
B1063

CONTROL UNIT 

Air bag diagnosis sensor unit is malfunctioning

Malfunction in air bag diagnosis sensor unit

SRC-38

< DTC/CIRCUIT DIAGNOSIS >

B1058, B1059, B1060, B1061, B1062, B1063 DIAGNOSIS SENSOR UNIT

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END