Nissan Pathfinder (2008 year). Manual - part 599

TM-134

< SYMPTOM DIAGNOSIS >

SYSTEM SYMPTOM

Vehicle Cannot Be Started from D

1

INFOID:0000000001282954

SYMPTOM:

Vehicle cannot be started from D

1

 on cruise test - Part 1 and cruise test - Part 2.

DIAGNOSTIC PROCEDURE

1.

CONFIRM THE SYMPTOM

Check if vehicle creeps in “R” position.
OK or NG

OK

>> GO TO 2.

NG

>> Refer to 

TM-130, "Vehicle Does Not Creep Backward in "R" Position"

. 

2.

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 3.

3.

CHECK ACCELERATOR PEDAL POSITION (APP) SENSOR

Check accelerator pedal position (APP) sensor. Refer to 

TM-75

.

OK or NG

OK

>> GO TO 4.

NG

>> Repair or replace accelerator pedal position (APP) sensor.

4.

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 5.

NG

>> Refill ATF.

5.

CHECK LINE PRESSURE

Check line pressure at the engine stall point. Refer to 

TM-187, "Line Pressure Test"

.

OK or NG

OK

>> GO TO 8.

NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.

6.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

OK or NG

OK

>> GO TO 8.

NG

>> Repair or replace damaged parts.

7.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

-

Power train system. Refer to 

TM-253

.

-

Transmission case. Refer to 

TM-253

.

OK or NG

SYSTEM SYMPTOM

TM-135

< SYMPTOM DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OK

>> GO TO 8.

NG

>> Repair or replace damaged parts.

8.

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

.

2.

Check A/T fluid condition. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 9.

NG

>> GO TO 12.

9.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.23).

OK or NG

OK

>> GO TO 10.

NG

>> Repair or replace damaged parts.

10.

CHECK SYMPTOM

Check again. Refer to 

TM-191, "Cruise Test - Part 1"

, 

TM-193, "Cruise Test - Part 2"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 11.

11.

PERFORM TCM INSPECTION

1.

Perform TCM input/output signals inspection. Refer to 

TM-113, "TCM Terminals and Reference Values"

.

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

12.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.23).

OK or NG

OK

>> GO TO 10.

NG

>> Repair or replace damaged parts.

A/T Does Not Shift: D

1

→

 D

2

INFOID:0000000001282955

SYMPTOM:

The vehicle does not shift-up from the D

1

 to D

2

 gear at the specified speed.

DIAGNOSTIC PROCEDURE

1.

CONFIRM THE SYMPTOM

Check if vehicle creeps forward in “D” position and vehicle can be started from D

1.

OK or NG

OK

>> GO TO 2.

NG

>> Refer to 

TM-132, "Vehicle Does Not Creep Forward in "D" Position"

, 

TM-134, "Vehicle Cannot Be

Started from D

1

"

.

2.

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 3.

TM-136

< SYMPTOM DIAGNOSIS >

SYSTEM SYMPTOM

3.

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4.

CHECK LINE PRESSURE

Check line pressure at the engine stall point. Refer to 

TM-187, "Line Pressure Test"

.

OK or NG

OK

>> GO TO 7.

NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.

5.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

-

Power train system. Refer to 

TM-253

.

-

Transmission case. Refer to 

TM-253

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

7.

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

.

2.

Check A/T fluid condition. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 8.

NG

>> GO TO 11.

8.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.10).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

9.

CHECK SYMPTOM

Check again. Refer to 

TM-191, "Cruise Test - Part 1"

, 

TM-193, "Cruise Test - Part 2"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 10.

10.

PERFORM TCM INSPECTION

1.

Perform TCM input/output signals inspection. Refer to 

TM-113, "TCM Terminals and Reference Values"

.

SYSTEM SYMPTOM

TM-137

< SYMPTOM DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

11.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.10).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

A/T Does Not Shift: D

2

→

 D

3

INFOID:0000000001282956

SYMPTOM:

The vehicle does not shift-up from D

2

 to D

3

 gear at the specified speed.

DIAGNOSTIC PROCEDURE

1.

CONFIRM THE SYMPTOM

Check if vehicle creeps forward in “D” position and vehicle can be started from D

1.

OK or NG

OK

>> GO TO 2.

NG

>> Refer to 

TM-132, "Vehicle Does Not Creep Forward in "D" Position"

, 

TM-134, "Vehicle Cannot Be

Started from D

1

"

.

2.

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 3.

3.

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4.

CHECK LINE PRESSURE

Check line pressure at the engine stall point. Refer to 

TM-187, "Line Pressure Test"

.

OK or NG

OK

>> GO TO 7.

NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.

5.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

TM-138

< SYMPTOM DIAGNOSIS >

SYSTEM SYMPTOM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

-

Power train system. Refer to 

TM-253

.

-

Transmission case. Refer to 

TM-253

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

7.

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

.

2.

Check A/T fluid condition. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 8.

NG

>> GO TO 11.

8.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.11).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

9.

CHECK SYMPTOM

Check again. Refer to 

TM-191, "Cruise Test - Part 1"

, 

TM-193, "Cruise Test - Part 2"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 10.

10.

PERFORM TCM INSPECTION

1.

Perform TCM input/output signals inspection. Refer to 

TM-113, "TCM Terminals and Reference Values"

.

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

11.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.11).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

A/T Does Not Shift: D

3

→

 D

4

INFOID:0000000001282957

SYMPTOM:

• The vehicle does not shift-up from the D

3

 to D

4

 gear at the specified speed.

DIAGNOSTIC PROCEDURE

1.

CONFIRM THE SYMPTOM

Check if vehicle creeps forward in “D” position and vehicle can be started from D

1.

OK or NG

OK

>> GO TO 2.

SYSTEM SYMPTOM

TM-139

< SYMPTOM DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

NG

>> Refer to 

TM-132, "Vehicle Does Not Creep Forward in "D" Position"

, 

TM-134, "Vehicle Cannot Be

Started from D

1

"

.

2.

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 3.

3.

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4.

CHECK LINE PRESSURE

Check line pressure at the engine stall point. Refer to 

TM-187, "Line Pressure Test"

.

OK or NG

OK

>> GO TO 7.

NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.

5.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

-

Power train system. Refer to 

TM-253

.

-

Transmission case. Refer to 

TM-253

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

7.

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

.

2.

Check A/T fluid condition. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 8.

NG

>> GO TO 11.

8.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.12).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

TM-140

< SYMPTOM DIAGNOSIS >

SYSTEM SYMPTOM

9.

CHECK SYMPTOM

Check again. Refer to 

TM-191, "Cruise Test - Part 1"

, 

TM-193, "Cruise Test - Part 2"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 10.

10.

PERFORM TCM INSPECTION

1.

Perform TCM input/output signals inspection. Refer to 

TM-113, "TCM Terminals and Reference Values"

.

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

11.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.12).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

A/T Does Not Shift: D

4

→

 D

5

INFOID:0000000001282958

SYMPTOM:

• The vehicle does not shift-up from the D

4 

to D

5

 gear at the specified speed.

• The vehicle does not shift-up from the D

4

 to D

5

 gear unless A/T is warmed up.

DIAGNOSTIC PROCEDURE

1.

CONFIRM THE SYMPTOM

Check if vehicle creeps forward in “D” position and vehicle can be started from D

1.

OK or NG

OK

>> GO TO 2.

NG

>> Refer to 

TM-132, "Vehicle Does Not Creep Forward in "D" Position"

, 

TM-134, "Vehicle Cannot Be

Started from D

1

"

.

2.

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

TM-35, "CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 3.

3.

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4.

CHECK LINE PRESSURE

Check line pressure at the engine stall point. Refer to 

TM-187, "Line Pressure Test"

.

OK or NG

OK

>> GO TO 7.

NG - 1 >> Line pressure high. GO TO 5.
NG - 2 >> Line pressure low. GO TO 6.

5.

DETECT MALFUNCTIONING ITEM

SYSTEM SYMPTOM

TM-141

< SYMPTOM DIAGNOSIS >

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

6.

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

.

2.

Disassemble A/T. Refer to 

TM-253

.

3.

Check the following.

-

Oil pump assembly. Refer to 

TM-271, "Exploded View"

.

-

Power train system. Refer to 

TM-253

.

-

Transmission case. Refer to 

TM-253

.

OK or NG

OK

>> GO TO 7.

NG

>> Repair or replace damaged parts.

7.

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

TM-199, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

.

2.

Check A/T fluid condition. Refer to 

TM-180, "Checking the A/T Fluid (ATF)"

.

OK or NG

OK

>> GO TO 8.

NG

>> GO TO 11.

8.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.13).

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

9.

CHECK SYMPTOM

Check again. Refer to 

TM-191, "Cruise Test - Part 1"

.

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 10.

10.

PERFORM TCM INSPECTION

1.

Perform TCM input/output signals inspection. Refer to 

TM-113, "TCM Terminals and Reference Values"

.

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

11.

DETECT MALFUNCTIONING ITEM

• Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

TM-152,

"Symptom Chart"

 (Symptom No.13). 

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.