Nissan Teana J32. Manual - part 1178

 

  Index      Nissan     Nissan Teana J32 (2008 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1176  1177  1178  1179   ..

 

 

Nissan Teana J32. Manual - part 1178

 

 

TM-236

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE 

SOLENOID VALVE)

P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE
PRESSURE SOLENOID VALVE)

Description

INFOID:0000000003806419

The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pres-
sure to suit the driving condition in response to the signal sent from the TCM.

DTC Logic

INFOID:0000000003806420

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Start engine and maintain the following conditions for at least 10 consecutive seconds. Test start from 0
km/h (0 MPH).

With GST

Follow the procedure “With CONSULT-III”.

Is “P0746 PRS CNT SOL/A FCTN” detected?

YES

>> Go to 

TM-236, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003806421

1.

CHECK LINE PRESSURE

Perform line pressure test. Refer to 

TM-308, "Inspection and Judgment"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts. Refer to 

TM-308, "Inspection and Judgment"

.

2.

CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) 

Check pressure control solenoid valve A (line pressure solenoid valve). Refer to 

TM-237, "Component Inspec-

tion [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]"

.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0746

PRS CNT SOL/A FCTN

Unexpected gear ratio was de-
tected in the low side due to ex-
cessively low line pressure.

• Line pressure control system
• Output speed sensor (sec-

ondary speed sensor)

• Input speed sensor (primary 

speed sensor)

ATF TEMP SEN

: 1.0 

 2.0 V

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

VEHICLE SPEED

: 10 km/h (6 MPH) More than

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the 
driving conditions required for this test.

P0746 PRESSURE CONTROL SOLENOID A PERFORMANCE (LINE PRESSURE 

SOLENOID VALVE)

TM-237

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK OUTPUT SPEED SENSOR (SECONDARY SPEED SENSOR) SYSTEM

Check output speed sensor (secondary speed sensor) system. Refer to 

TM-222, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK INPUT SPEED SENSOR (PRIMARY SPEED SENSOR) SYSTEM

Check input speed sensor (primary speed sensor) system. Refer to 

TM-218, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace the TCM. Refer to 

TM-315, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid 
Valve)]

INFOID:0000000003806422

1.

CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check resistance between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the transaxle assembly. Refer to 

TM-332, "Exploded View"

.

CVT unit harness connector

Ground

Resistance (Approx.)

Connector

Terminal

F24

2

3.0 – 9.0 

TM-238

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE 

SOLENOID VALVE)

P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRES-
SURE SOLENOID VALVE)

Description

INFOID:0000000003806423

The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the secondary pressure
to suit the driving condition in response to a signal sent from the TCM.

DTC Logic

INFOID:0000000003806424

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.
Perform the following procedure to confirm the malfunction is eliminated after the repair.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Start engine and maintain the following conditions for at least 30 consecutive seconds.

With GST

Follow the procedure “With CONSULT-III”.

Is “P0776 PRS CNT SOL/B FCTN” detected?

YES

>> Go to 

TM-238, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003806425

1.

CHECK LINE PRESSURE

Perform line pressure test. Refer to 

TM-308, "Inspection and Judgment"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts. Refer to 

TM-308, "Inspection and Judgment"

.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0776

PRS CNT SOL/B FCTN

Secondary pressure is too high 
or too low compared with the 
commanded value while driv-
ing.

• Harness or connectors

(Solenoid circuit is open or 
shorted.)

• Pressure control solenoid 

valve B (secondary pressure 
solenoid valve system)

• Transmission fluid pressure 

sensor A (secondary pres-
sure sensor)

• Line pressure control system

ATF TEMP SEN

: 1.0 

 2.0 V

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

VEHICLE SPEED

: 10 km/h (6 MPH) More than

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the 
driving conditions required for this test.

P0776 PRESSURE CONTROL SOLENOID B PERFORMANCE (SEC PRESSURE 

SOLENOID VALVE)

TM-239

< COMPONENT DIAGNOSIS >

[CVT: RE0F10A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)

Check pressure control solenoid valve B (Secondary pressure solenoid valve). Refer to 

TM-239, "Component

Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check pressure control solenoid valve A (Line pressure solenoid valve). Refer to 

TM-239, "Component

Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYS-

TEM

Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to 

TM-242, "DTC

Logic"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace the TCM. Refer to 

TM-315, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid 
Valve)]

INFOID:0000000003806426

1.

CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check resistance between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the transaxle assembly. Refer to 

TM-332, "Exploded View"

.

Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure So-
lenoid Valve)]

INFOID:0000000003806427

1.

CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)

Check resistance between CVT unit harness connector terminal and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the transaxle assembly. Refer to 

TM-332, "Exploded View"

.

CVT unit harness connector

Ground

Resistance (Approx.)

Connector

Terminal

F24

2

3.0 – 9.0 

CVT unit harness connector

Ground

Resistance (Approx.)

Connector

Terminal

F24

3

3.0 – 9.0 

 

 

 

 

 

 

 

Content   ..  1176  1177  1178  1179   ..