Nissan Teana J32. Manual - part 1134

TM-60

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

P0730 BELT DAMAGE

P0730 BELT DAMAGE

Description

INFOID:0000000003848973

TCM selects the gear ratio using the engine load (throttle position), the primary pulley revolution speed, and
the secondary pulley revolution speed as input signals. Then it changes the operating pressure of the primary
pulley and the secondary pulley and changes the groove width of the pulley.

DTC Logic

INFOID:0000000003848974

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Make sure that output voltage of CVT fluid temperature sensor is within the range below.

4.

Start engine and maintain the following conditions for at least 30 consecutive seconds.

Is “P0730 BELT DAMG” detected?

YES

>> Go to 

TM-60, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003848975

1.

CHECK DTC 

With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “Self-Diagnostic Results” mode for “TRANSMISSION”.

Are any DTC detected?

YES-1 (DTC for “P0730 BELT DAMG” is detected)>>Replace  transaxle  assembly.  Refer  to 

TM-168,

"Exploded View"

.

YES-2 (DTC except for “P0730 BELT DAMG” is detected)>>Check DTC detected item. Refer to 

TM-37,

"CONSULT-III Function (TRANSMISSION)"

.

NO

>> GO TO 2.

2.

DETECT MALFUNCTIONING ITEMS

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0730

BELT DAMG

Unexpected gear ratio detected.

Transaxle assembly

ATF TEMP SEN

: 1.0 – 2.0 V

If it is out of range, drive the vehicle to decrease the voltage (warm up the fluid) or stop engine to increase the voltage 
(cool down the fluid)

Start test from 0 km/h (0 MPH)

Constant acceleration

: Keep 30 sec or more

VEHICLE SPEED

: 10 km/h (6 MPH) or more

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

ENG SPEED

: 450 rpm or more

P0730 BELT DAMAGE

TM-61

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-153, "Exploded View"

.

NO

>> Repair or replace damaged parts.

TM-62

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE

P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE

Description

INFOID:0000000003848976

• The torque converter clutch solenoid valve is activated by the TCM in response to signals sent from the vehi-

cle speed and accelerator pedal position sensors. Lock-up piston operation will then be controlled.

• Lock-up operation, however, is prohibited when CVT fluid temperature is too low.
• When the accelerator pedal is depressed (less than 2.0/8) in lock-up condition, the engine speed shall not

change abruptly. If there is a big jump in engine speed, there is no lock-up.

DTC Logic

INFOID:0000000003848977

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Wait at least 10 consecutive seconds.

3.

Perform “Self-Diagnostic Results” mode for “TRANSMISSION”.

With GST

Follow the procedure “With CONSULT-III”.

Is “P0740 TCC SOLENOID/CIRC” detected?

YES

>> Go to 

TM-62, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003848978

1.

CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check resistance between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK HARNESS BETWEEN TCM AND CVT UNIT (TORQUE CONVERTER CLUTCH SOLENOID

VALVE) (PART 1)

1.

Disconnect CVT unit connector.

2.

Check continuity between TCM vehicle side harness connector terminal and CVT unit vehicle side har-
ness connector terminal.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0740

TCC SOLENOID/CIRC

Normal voltage is not applied to solenoid 
due to open or short circuit.

• Torque converter clutch solenoid valve
• Harness or connectors

(Solenoid circuit is open or shorted.)

TCM vehicle side harness connector

Ground

Resistance (Approx.)

Connector

Terminal

F23

38

3.0 – 9.0 

Ω

P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE

TM-63

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN TCM AND CVT UNIT (TORQUE CONVERTER CLUTCH SOLENOID

VALVE) (PART 2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check torque converter clutch solenoid valve. Refer to 

TM-63, "Component Inspection (Torque Converter

Clutch Solenoid Valve)"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace transaxle assembly. Refer to 

TM-168, "Exploded View"

.

5.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-153, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection (Torque Converter Clutch Solenoid Valve)

INFOID:0000000003848979

1.

CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE

Check resistance between CVT unit connector terminal and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace transaxle assembly. Refer to 

TM-168, "Exploded View"

.

TCM vehicle side harness connector

CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

38

F24

12

Existed

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

38

Not existed

CVT unit connector

Ground

Resistance (Approx.)

Connector

Terminal

F24

12

3.0 – 9.0 

Ω