Nissan Teana J32. Manual - part 1131

TM-48

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

P0705 PARK/NEUTRAL POSITION SWITCH

NO

>> GO TO 2.

2.

 CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

 CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-153, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000003848959

1.

CHECK PNP SWITCH

Check the continuity of the PNP switch by changing selector lever to various positions and checking continuity
between CVT unit terminals and ground.

 TCM vehicle side harness connector

 CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

1

F24

5

Existed

2

14

3

15

4

18

11

4

TCM vehicle side harness connector

Ground

Continuity

Connector Terminal

F23

1

Not existed

2

3

4

11

P0705 PARK/NEUTRAL POSITION SWITCH

TM-49

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace transaxle assembly. Refer to 

TM-168, "Exploded View"

.

Shift position

CVT unit connector

Ground

Continuity

Connector

Terminal

P

F24

4, 5, 14, 15, 18

Not existed

R

4, 15

Existed

5, 14, 18

Not existed

N

4, 5

Existed

14, 15, 18

Not existed

D

4, 5, 14, 15, 18

Existed

L

5, 14, 18

Existed

4, 15

Not existed

TM-50

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

P0710 CVT FLUID TEMPERATURE SENSOR

P0710 CVT FLUID TEMPERATURE SENSOR

Description

INFOID:0000000003848960

The CVT fluid temperature sensor detects the CVT fluid temperature and sends the signal to the TCM.

DTC Logic

INFOID:0000000003848961

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Start engine and maintain the following conditions for at least 10 minutes (total).

With GST

Follow the procedure “With CONSULT-III”.

Is “P0710 ATF TEMP SEN/CIRC” detected?

YES

>> Go to 

TM-50, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-35, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003848962

1.

CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check resistance between TCM vehicle side harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 1)

1.

Disconnect CVT unit connector.

DTC

Item

(CONSULT-III screen term)

Malfunction is detected when...

Possible cause

P0710

ATF TEMP SEN/CIRC

During running, the CVT fluid temperature 
sensor signal voltage is excessively high or 
low.

• Harness or connectors

(Sensor circuit is open or shorted.)

• CVT fluid temperature sensor

VEHICLE SPEED

: 10 km/h (6 MPH) or more

ENG SPEED

: 450 rpm or more

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

TCM vehicle side harness connector

condition

Resistance (Approx.)

Connector

Terminal

F23

13

25

When CVT fluid temperature is 20

°

C (68

°

F)

6.5 k

Ω

When CVT fluid temperature is 80

°

 (176

°

F)

0.9 k

Ω

P0710 CVT FLUID TEMPERATURE SENSOR

TM-51

< COMPONENT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK CVT FLUID TEMPERATURE SENSOR

Check CVT fluid temperature sensor. Refer to 

TM-51, "Component Inspection (CVT Fluid Temperature Sen-

sor)"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace transaxle assembly. Refer to 

TM-168, "Exploded View"

.

5.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-153, "Exploded View"

.

NO

>> Repair or replace damaged parts.

Component Inspection (CVT Fluid Temperature Sensor)

INFOID:0000000003848963

1.

CHECK CVT FLUID TEMPERATURE SENSOR

Check resistance between CVT unit connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace transaxle assembly. Refer to 

TM-168, "Exploded View"

.

TCM vehicle side harness connector

CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

13

F24

17

Existed

25

19

TCM vehicle side harness connector

Ground

Continuity

Connector

Terminal

F23

13

Not existed

25

CVT unit connector

Condition

Resistance (Approx.)

Connector

terminal

F24

17

19

When CVT fluid temperature is 20

°

C (68

°

F)

6.5 k

Ω

When CVT fluid temperature is 80

°

C (176

°

F)

0.9 k

Ω