Nissan Teana J32. Manual - part 1081

SRC-78

< COMPONENT DIAGNOSIS >

B1120, B1121 SATELLITE SENS LH

B1120, B1121 SATELLITE SENS LH

Description

INFOID:0000000003814023

Main “G” sensor generates signal voltage, when it detects deceleration beyond the specified level by vehicle
side collision.

OPERATION

When air bag diagnosis sensor unit defines both signal voltage of the “G” sensor and the safing algorithm to
be that of collision which exceeds a specified level, the driving circuit switches on and feeds the electric ignitor
of both the front side air bag and side curtain air bag.

STRUCTURE

Integrated type of the “G” sensor element for side collision with output terminals for signal voltage.

INSTALLATION

LH satellite sensor is installed at the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000003814024

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-10, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-78, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003814025

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Replace wiring harness.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1120
B1121

SATELLITE SENS LH 
[COMM FAIL]
[UNMATCH]

LH satellite sensor is out of order

• Disconnection of wiring harness
• Malfunction in LH satellite sensor
• Malfunction in air bag diagnosis sen-

sor unit

B1120, B1121 SATELLITE SENS LH

SRC-79

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

3.

REPLACE SATELLITE SENSOR

1.

Replace LH satellite sensor. Refer to 

SR-20, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-78, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4. 

NO

>> INSPECTION END

4.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-78, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END

SRC-80

< COMPONENT DIAGNOSIS >

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

Description

INFOID:0000000003814026

Check the whole SRS and displays the malfunction either by illuminating or blinking the air bag warning lamp
in the combination meter. Malfunctioning part can be detected by on board self-diagnosis system and CON-
SULT-III.

OPERATION

It detects a shock that exceeds a specified level and monitors whether the driver and passenger air bags, front
side air bag, side curtain air bag and pre-tensioner seat belts operate normally. 

STRUCTURE

It contains the “G” sensors for both frontal and side collisions and spare battery function in case of main bat-
tery damage in collision.

INSTALLATION

Air bag diagnosis sensor unit is installed under the center console with fixed bolts.

DTC Logic

INFOID:0000000003814027

DTC CONFIRMATION PROCEDURE

1.

CHECK SELF-DIAG RESULT

 With CONSULT-III

1.

Turn ignition switch ON.

2.

Perform “AIR BAG” Self Diagnostic Result.

 Without CONSULT-III

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status. Refer to 

SRC-10, "Air Bag Warning Lamp Diagnosis"

.

NOTE:
SRS does not enter Diagnosis mode if no malfunction is detected in User mode.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-80, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003814028

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1122
B1123
B1124
B1125
B1126
B1127

CONTROL UNIT 

Air bag diagnosis sensor unit is mal-
functioning or out of the specification

• Malfunction in air bag diagnosis sen-

sor unit

• Configuration in air bag diagnosis 

sensor unit dose not match to the ve-
hicles specification

B1122, B1123, B1124, B1125, B1126, B1127 DIAGNOSIS SENSOR UNIT

SRC-81

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-22, "Exploded View"

.

2.

Perform DTC confirmation procedure. Refer to 

SRC-80, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1. 

NO

>> INSPECTION END