Nissan Murano Z51. Manual - part 959

 

  Главная      Nissan     Nissan Murano Z51 (2010 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  957  958  959  960   ..

 

 

Nissan Murano Z51. Manual - part 959

 

 

LAN-42

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

MAIN LINE BETWEEN ADP AND PWBD CIRCUIT

MAIN LINE BETWEEN ADP AND PWBD CIRCUIT

Diagnosis Procedure

INFOID:0000000005514809

1.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Disconnect the following harness connectors.

-

ECM

-

Harness connectors B460 and B19

-

Automatic back door control unit

4.

Check the continuity between the harness connector and the automatic back door control unit harness
connector.

Is the inspection result normal?

YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the driver seat control unit and the automatic

back door control unit. 

NO

>> Repair the main line between the harness connector B19 and the automatic back door control

unit.

Harness connector

Automatic back door control unit harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

B19

2

B8

6

Existed

9

7

Existed

LAN

MAIN LINE BETWEEN PWBD AND M&A CIRCUIT

LAN-43

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

MAIN LINE BETWEEN PWBD AND M&A CIRCUIT

Diagnosis Procedure

INFOID:0000000005514810

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).

-

Harness connector B11

-

Harness connector M77

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Disconnect the following harness connectors.

-

Automatic back door control unit

-

Harness connectors B11 and M77

2.

Check the continuity between the automatic back door control unit harness connector and the harness
connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair the main line between the automatic back door control unit and the harness connector

B11.

3.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Disconnect the connector of combination meter.

2.

Check the continuity between the harness connector and the combination meter harness connector.

Is the inspection result normal?

YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the automatic back door control unit and the

combination meter. 

NO

>> Repair the main line between the harness connector M77 and the combination meter.

Automatic back door control unit harness connector

Harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

B8

6

B11

57

Existed

7

56

Existed

Harness connector

Combination meter harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

M77

57

M34

21

Existed

56

22

Existed

LAN-44

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

MAIN LINE BETWEEN M&A AND DLC CIRCUIT

MAIN LINE BETWEEN M&A AND DLC CIRCUIT

Diagnosis Procedure

INFOID:0000000005514811

1.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Disconnect the following harness connectors.

-

ECM

-

Combination meter

4.

Check the continuity between the combination meter harness connector and the data link connector.

Is the inspection result normal?

YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the combination meter and the data link con-

nector. 

NO

>> Repair the main line between the combination meter and the data link connector.

Combination meter harness connector

Data link connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

M34

21

M4

6

Existed

22

14

Existed

LAN

MAIN LINE BETWEEN DLC AND TCM CIRCUIT

LAN-45

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

MAIN LINE BETWEEN DLC AND TCM CIRCUIT

Diagnosis Procedure

INFOID:0000000005514812

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).

-

Harness connector M11

-

Harness connector E105

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Disconnect the harness connectors M11 and E105.

2.

Check the continuity between the data link connector and the harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair the main line between the data link connector and the harness connector M11.

3.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Disconnect the harness connectors E6 and F123.

2.

Check the continuity between the harness connectors.

Is the inspection result normal?

YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the data link connector and the TCM. 
NO

>> Repair the main line between the harness connectors E105 and E6.

Data link connector

Harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

M4

6

M11

12

Existed

14

11

Existed

Harness connector

Harness connector

Continuity

Connector No.

Terminal No.

Connector No.

Terminal No.

E105

12

E6

1

Existed

11

8

Existed

 

 

 

 

 

 

 

содержание   ..  957  958  959  960   ..