Nissan Murano Z51. Manual - part 1425

P0710 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-51

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace transaxle assembly. Refer to 

TM-173, "Exploded View"

.

CVT unit connector

Condition

Resistance (Approx.)

Connector

Terminal

F24

17

19

When CVT fluid temperature is 20

°

C (68

°

F)

6.5 k

Ω

When CVT fluid temperature is 80

°

C (176

°

F)

0.9 k

Ω

TM-52

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

P0715 INPUT SPEED SENSOR A

P0715 INPUT SPEED SENSOR A

Description

INFOID:0000000005513980

The primary speed sensor detects the primary pulley revolution speed and sends a signal to the TCM.

DTC Logic

INFOID:0000000005513981

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
Immediately after performing any “DTC CONFIRMATION PROCEDURE”, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

With CONSULT-III

1.

Turn ignition switch ON.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Start engine and maintain the following conditions for at least 5 consecutive seconds.

 With GST

Follow the procedure “With CONSULT-III”.
Is “P0715” detected?

YES

>> Go to 

TM-52, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000005513982

1.

CHECK PRIMARY SPEED SENSOR

1.

Start engine.

2.

Check voltage between TCM connector terminals.

3.

If OK, check the pulse when vehicle drive.

DTC

Trouble diagnosis name

DTC is detected if...

Possible cause

P0715

Input/Turbine Speed Sensor 
A Circuit

• Primary speed sensor signal is not input 

due to an open circuit.

• An unexpected signal is input when vehi-

cle is being driven.

• Harness or connectors

(Sensor circuit is open or shorted.)

• Primary speed sensor

VEHICLE SPEED

: 10 km/h (6 MPH) or more

ACC PEDAL OPEN

: More than 1.0/8

RANGE

: “D” position

ENG SPEED

: 450 rpm or more

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the driving 
conditions required for this test.

TCM connector

Voltage (Approx.)

Connector

Terminal

F23

25

26

4.75 – 5.25 V

TCM connector

Condition

Voltage (Approx.) 

Connector

Terminal

F23

33

When driving [“L”position, 20 km/h (12 MPH)]

680 Hz

P0715 INPUT SPEED SENSOR A

TM-53

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES 

>> GO TO 7.

NO-1

>> Battery voltage is not supplied: GO TO 2.

NO-2

>> Battery voltage is supplied, but there is a malfunction in the frequency: GO TO 4.

2.

 CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND

SENSOR GROUND) (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM vehicle side harness connector terminals and CVT unit vehicle side har-
ness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

 CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND

SENSOR GROUND) (PART 2)

Check continuity between TCM vehicle side harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

4.

 CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR  (PRIMARY SPEED SEN-

SOR) (PART 1)

1.

Turn ignition switch OFF.

2.

Check continuity between TCM vehicle side harness connector terminal and CVT unit vehicle side har-
ness connector terminal.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

 CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (PRIMARY SPEED SEN-

SOR) (PART 2)

Check continuity between TCM vehicle side harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 6.

TCM vehicle side harness connector

CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

25

F24

19

Existed

26

20

TCM vehicle side harness connector 

Ground

Continuity

Connector

Terminal

F23

25

Not existed

26

TCM vehicle side harness connector 

CVT unit vehicle side harness connector

Continuity

Connector

Terminal

Connector

Terminal

F23

33

F24

22

Existed

TCM vehicle side harness connector 

Ground

Continuity

Connector

Terminal

F23

33

Not existed

TM-54

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F09B]

P0715 INPUT SPEED SENSOR A

>> Repair or replace damaged parts.

6.

 CHECK THE TCM SHORT

1.

Replace with the same type of TCM. Refer to 

TM-160, "Exploded View"

.

2.

Connect each connectors.

3.

Perform “DTC CONFIRMATION PROCEDURE”. Refer to 

TM-52, "DTC Logic"

.

Is the “P0715” detected again?

YES

>> GO TO 7.

NO

>> Check intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

7.

DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace TCM. Refer to 

TM-160, "Exploded View"

.

NO

>> Repair or replace damaged parts.