Nissan Murano Z51. Manual - part 1344

SRC-146

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1202, B1203, B1204, B1205, B1206, B1207 DIAGNOSIS SENSOR UNIT

>> GO TO 2.

2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-159

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005513672

With CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connectors.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace wiring harness.

3.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit.

2.

Check the screen of CONSULT-III.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Check the intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

B1209 FRONTAL COLLISION DETECTION

SRC-147

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1209 FRONTAL COLLISION DETECTION

Description

INFOID:0000000005513673

DTC B1209 FRONTAL COLLISION DETECTION

When detect a component damage resulting from a front collision, blinks or illuminates the air bag warning
lamp to inform the driver. Malfunctioning can be detected by the CONSULT-III.

OPERATION

The air bags and seat belt pre-tensioners for driver and front passenger are operated by the decision of the air
bag diagnosis sensor unit out signal transmitted because of the frontal collision.

STRUCTURE

It consists of crash zone sensor, air bag diagnosis sensor unit, air bags and seat belt pre-tensioners for driver
and front passenger.

INSTALLATION

Refer to 

SR-21, "Removal and Installation"

, 

SR-25, "Removal and Installation"

, 

SR-27, "Removal and Installa-

tion"

, 

SR-11, "Removal and Installation"

, 

SR-17, "Removal and Installation"

.

DTC Logic

INFOID:0000000005513674

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.
Is malfunctioning part detected?

YES

>> Refer to 

SRC-147, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005520170

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis.Refer to 

SR-5, "FOR FRONTAL COLLISION : When SRS is activated in a colli-

sion"

 or 

SR-6, "FOR FRONTAL COLLISION : When SRS is not activated in a collision"

.

Iscollision diagnosis complete?

YES

>> GO TO 2.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1209

FRONTAL COLLISION 
DETECTION

Front seat belt pre-tensioner, front air 
bag is deployed

—

SRC-148

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1209 FRONTAL COLLISION DETECTION

NO

>> INSPECTION END

2.

FINAL INSPECTION

Perform “AIR BAG” Self Diagnostic Result.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Peform diagnosis of applicable DTC.Refer to 

SRC-159, "DTC Index"

.

B1210 SIDE COLLISION DETECTION

SRC-149

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1210 SIDE COLLISION DETECTION

Description

INFOID:0000000005513676

DTC B1210 SIDE COLLISION DETECTION

When detect a component damage resulting from a side collision, brinks or illuminates the air bag warning
lamp to inform the driver. Malfunctioning can be detected by the CONSULT-III.

OPERATION

The front side air bag and side curtain air bag are operated by the decision of the air bag diagnosis sensor unit
signal of the side collision.

STRUCTURE

It consists of satellite sensor, air bag diagnosis sensor unit, front side air bag and side curtain air bag. 

INSTALLATION

Refer to 

SR-23, "Removal and Installation"

, 

SR-25, "Removal and Installation"

, 

SR-19, "Removal and Installa-

tion"

.

DTC Logic

INFOID:0000000005513677

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-III)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-149, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005520171

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device. 

1.

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis.Refer to 

SR-7, "FOR SIDE AND ROLLOVER COLLISION : When SRS is activated

in a collision"

 or 

SR-8, "FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision"

.

Iscollision diagnosis complete?

YES

>> GO TO 2.

NO

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1210

SIDE COLLISION DE-
TECTION

Front side air bag, side curtain air bag is 
deployed

—