Nissan Murano Z51. Manual - part 1326

SRC-74

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1081 PRE-TEN FRONT RH

>> GO TO 2.

2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-159

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005513564

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Repair or replace wiring harness.

3.

CHECK FRONT SEAT BELT PRE-TENSIONER

1.

Replace front RH seat belt pre-tensioner.

2.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Check the intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

B1082 PRE-TEN FRONT RH

SRC-75

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1082 PRE-TEN FRONT RH

Description

INFOID:0000000005513565

DTC B1082 [VB-SHORT] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main "G" sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects
the deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000005513566

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-76, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1082

PRE-TEN FRONT RH 
[VB-SHORT]

Front RH seat belt pre-tensioner circuit 
is shorted to some power supply circuit

• Disconnection of wiring harness and 

short

• Internal breakdown in front RH seat 

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit

SRC-76

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1082 PRE-TEN FRONT RH

>> GO TO 2.

2.

CHECK AIR BAG WARNING LAMP

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart.

SRC-159

.

NO

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000005513567

With CONSULT-lll

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device. 

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3. 

NO

>> Repair or replace wiring harness.

3.

CHECK FRONT SEAT BELT PRE-TENSIONER

1.

Replace front RH seat belt pre-tensioner.

2.

Check the screen of CONSULT-lll.

Is the inspection result normal?

YES

>> INSPECTION END.

NO

>> Check the intermittent incident. Refer to 

GI-39, "Intermittent Incident"

.

B1083 PRE-TEN FRONT RH

SRC-77

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B1083 PRE-TEN FRONT RH

Description

INFOID:0000000005513568

DTC B1083 [GND-SHORT] PRE-TEN FRONT RH

For front RH seat belt pre-tensioner, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In case of frontal collision that exceeds specified impact level, the air bag diagnosis sensor unit detects the
deceleration caused by collision. It restrains the passenger with seat belt easing the stress on passengers
chest with load limiter.

STRUCTURE

The restraint system for front seat occupant consists of the pre-tensioner mechanism and load limiter mecha-
nism.

INSTALLATION

Front RH seat belt pre-tensioner is installed on the underside of center pillar with fixed nuts.

DTC Logic

INFOID:0000000005513569

DTC DETECTION LOGIC

With CONSULT-lll

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (With CONSULT-lll)

1.

INSPECTION START

Turn ignition switch ON.

>> GO TO 2.

2.

CHECK SELF-DIAG RESULT

Check the screen of CONSULT-lll.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-78, "Diagnosis Procedure"

.

NO

>> INSPECTION END.

DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

INSPECTION START

Turn ignition switch ON.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1083

PRE-TEN FRONT RH 
[GND-SHORT]

Front RH seat belt pre-tensioner circuit 
is shorted to ground

• Disconnection of wiring harness and 

short

• Internal breakdown in front RH seat 

belt pre-tensioner

• Internal breakdown in air bag diag-

nosis sensor unit