Nissan Murano Z51. Manual - part 1207

 

  Главная      Nissan     Nissan Murano Z51 (2010 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1205  1206  1207  1208   ..

 

 

Nissan Murano Z51. Manual - part 1207

 

 

SE-16

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

YES

>> Replace the blown fusible link after repairing the affected circuit if a fusible link is blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Check voltage between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>>

Check the following.

• Repair or replace harness between fusible link and automatic drive positioner control unit.
• Circuit breaker.

3.

CHECK GROUND CIRCUIT

Check continuity between the automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair harness or connector.

(+)

(–)

Voltage (V)

(Approx.)

Automatic drive positioner control unit

Connector

Terminals

M104

25

Ground

Battery voltage

Automatic drive positioner control unit

Ground

Continuity 

Connector

Terminal

M104

30

Existed

FRONT POWER RETURN SWITCH

SE-17

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

FRONT POWER RETURN SWITCH

LH

LH : Description

INFOID:0000000005518147

Switch that performs the return operation.

LH : Component Function Check

INFOID:0000000005518148

1.

CHECK FUNCTION

Check that the rear seatback (LH) rises when pressing and holding the front power return switch (LH). 

Is the inspection result normal?

YES

>> Front power return switch (LH) is OK.

NO

>> Refer to

SE-17, "LH : Diagnosis Procedure"

.

LH : Diagnosis Procedure

INFOID:0000000005518149

1.

CHECK REAR SEATBACK POWER RETURN CONTROL UNIT INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power return switch (LH) connector.

3.

Check voltage between front power return switch (LH) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK FRONT POWER RETURN SWITCH (LH) CIRCUIT

1.

Disconnect rear seatback power return control unit connector.

2.

Check continuity between rear seatback power return control unit harness connector and front power
return switch (LH) harness connector. 

3.

Check continuity between rear seatback power return control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear seatback return control unit. Refer to 

SE-133, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK FRONT POWER RETURN SWITCH (LH) GROUND CIRCUIT

Check continuity front power return switch (LH) harness connector and ground. 

(+)

(–)

Voltage (V)

(Approx.)

Front power return switch (LH)

Connector

Terminal

M114

1

Ground

5

Rear seatback power return control unit

Front power return switch (LH)

Continuity 

Connector

Terminal

Connector

Terminal

B493

28

M114

1

Existed

Rear seatback power return control unit

Ground

Continuity 

Connector

Terminal

M493

28

Not existed

Front power return switch (LH)

Ground

Continuity 

 Connector

Terminal

M114

2

Existed

SE-18

< DTC/CIRCUIT DIAGNOSIS >

FRONT POWER RETURN SWITCH

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK FRONT POWER RETURN SWITCH (LH)

Check front power return switch (LH). 
Refer to

SE-18, "LH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace front power return switch (LH). Refer to 

SE-138, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

LH : Component Inspection

INFOID:0000000005518150

1.

CHECK FRONT POWER RETURN SWITCH (LH)

1.

Turn ignition OFF.

2.

Disconnect front power return switch (LH) connector.

3.

Check front power return switch (LH) terminals.

Is the inspection result normal?

YES

>> Front power return switch (LH) is OK.

NO

>> Replace front power return switch (LH). Refer to 

SE-138, "Removal and Installation"

.

RH

RH : Description

INFOID:0000000005518151

Switch that performs the return operation.

RH : Component Function Check

INFOID:0000000005518152

1.

CHECK FUNCTION

Check that the rear seatback (RH) rises when pressing and holding the front power return switch (RH). 
Is the inspection result normal?

YES

>> Front power return switch (RH) is OK.

NO

>> Refer to

SE-18, "RH : Diagnosis Procedure"

.

RH : Diagnosis Procedure

INFOID:0000000005518153

1.

CHECK REAR SEATBACK POWER RETURN CONTROL UNIT OUTPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power return switch (RH) connector.

3.

Check voltage between front power return switch (RH) harness connector and ground.

Is the inspection result normal?

Front power return switch (LH) connector Terminal

Condition

Continuity

M114

1

2

Front power return switch (LH) is pressed

Existed

Front power return switch (LH) is released

Not existed

(+)

(–)

Voltage (V)

(Approx.)

Front power return switch (RH)

Connector

Terminal

M113

1

Ground

5

FRONT POWER RETURN SWITCH

SE-19

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK FRONT POWER RETURN SWITCH (RH) CIRCUIT

1.

Disconnect rear seatback power return control unit connector.

2.

Check continuity between rear seatback power return control unit harness connector and front power
return switch (RH) harness connector. 

3.

Check continuity between rear seatback power return control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear seatback power return control unit. Refer to 

SE-133, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK FRONT POWER RETURN SWITCH (RH) GROUND CIRCUIT

Check continuity front power return switch (RH) harness connector and ground. 

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK FRONT POWER RETURN SWITCH (RH)

Check front power return switch (RH). 
Refer to

SE-19, "RH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace front power return switch (RH). Refer to 

SE-138, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

RH : Component Inspection

INFOID:0000000005518154

1.

CHECK FRONT POWER RETURN SWITCH (RH)

1.

Turn ignition OFF.

2.

Disconnect front power return switch (RH) connector.

3.

Check front power return switch (RH) terminals.

Is the inspection result normal?

YES

>> Front power return switch (RH) is OK.

Rear seatback power return control unit

Front power return switch (RH)

Continuity 

Connector

Terminal

Connector

Terminal

B493

20

M113

1

Existed

Rear seatback power return control unit

Ground

Continuity 

Connector

Terminal

B493

20

Not existed

Front power return switch (RH)

Ground

Continuity 

 Connector

Terminal

M113

2

Existed

Front power return switch (RH) connector Terminal

Condition

Continuity

M113

1

2

Front power return switch (RH) is pressed

Existed

Front power return switch (RH) is released

Not existed

 

 

 

 

 

 

 

содержание   ..  1205  1206  1207  1208   ..