Nissan Murano Z51. Manual - part 1127

 

  Главная      Nissan     Nissan Murano Z51 (2010 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1125  1126  1127  1128   ..

 

 

Nissan Murano Z51. Manual - part 1127

 

 

PWC-3

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

WHEN BOTH POWER WINDOW MAIN SWITCH 
AND REAR POWER WINDOW SWITCH RH ARE 
OPERATED : Diagnosis Procedure  ......................

108

AUTO OPERATION DOES NOT OPERATE 
BUT MANUAL OPERATES NORMALLY  ........

109

DRIVER SIDE  ..........................................................

109

DRIVER SIDE : Diagnosis Procedure  ...................

109

PASSENGER SIDE  .................................................

109

PASSENGER SIDE : Diagnosis Procedure  ..........

109

ANTI-PINCH FUNCTION DOES NOT OPER-
ATE NORMALLY  .............................................

110

DRIVER SIDE  ..........................................................

110

DRIVER SIDE : Diagnosis Procedure  ...................

110

PASSENGER SIDE  .................................................

110

PASSENGER SIDE : Diagnosis Procedure  ..........

110

POWER WINDOW RETAINED POWER OP-
ERATION DOES NOT OPERATE PROPERLY 

..

111

Diagnosis Procedure .............................................

111

DOOR KEY CYLINDER SWITCH DOES NOT 
OPERATE POWER WINDOWS  .......................

112

Diagnosis Procedure .............................................

112

KEYLESS POWER WINDOW DOWN DOES 
NOT OPERATE  ................................................

113

Diagnosis Procedure .............................................

113

POWER WINDOW LOCK SWITCH DOES 
NOT FUNCTION ..............................................

114

Diagnosis Procedure  .............................................

114

POWER WINDOW SWITCH ILLUMINATION 
DOES NOT ILLUMINATE  ...............................

115

Diagnosis Procedure  .............................................

115

PRECAUTION ............................................

116

PRECAUTIONS ...............................................

116

FOR USA AND CANADA  ........................................

116

FOR USA AND CANADA : Precaution for Supple-
mental Restraint System (SRS) "AIR BAG" and 
"SEAT BELT PRE-TENSIONER" ..........................

116

FOR USA AND CANADA : Precaution for Proce-
dure without Cowl Top Cover  ................................

116

FOR USA AND CANADA : Precaution Necessary 
for Steering Wheel Rotation after Battery Discon-
nect ........................................................................

116

FOR MEXICO ...........................................................

117

FOR MEXICO : Precaution for Supplemental Re-
straint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER" ................................................

117

FOR MEXICO : Precaution for Procedure without 
Cowl Top Cover .....................................................

118

FOR MEXICO : Precaution Necessary for Steer-
ing Wheel Rotation after Battery Disconnect .........

118

REMOVAL AND INSTALLATION  .............

119

POWER WINDOW MAIN SWITCH  .................

119

Exploded View .......................................................

119

Removal and Installation  .......................................

119

PWC-4

< BASIC INSPECTION >

DIAGNOSIS AND REPAIR WORK FLOW

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000005513308

DETAILED FLOW

1.

OBTAIN INFORMATION ABOUT SYMPTOM

Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.

>> GO TO 2.

2.

REPRODUCE THE MALFUNCTION INFORMATION

Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.

>> GO TO 3.

3.

IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”

Use “Symptom diagnosis” from the symptom inspection result in step 2 and then identify where to start per-
forming the diagnosis based on possible causes and symptoms.

>> GO TO 4.

4.

IDENTIFY THE MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”

Perform the diagnosis with “Component diagnosis” of the applicable system.

>> GO TO 5.

5.

REPAIR OR REPLACE THE MALFUNCTIONING PARTS

Repair or replace the specified malfunctioning parts.

>> GO TO 6.

6.

FINAL CHECK

Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 2.

Are the malfunctions corrected?

YES

>> INSPECTION END

NO

>> GO TO 3.

INSPECTION AND ADJUSTMENT

PWC-5

< BASIC INSPECTION >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

INSPECTION AND ADJUSTMENT

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : De-
scription

INFOID:0000000005513309

When battery negative terminal is disconnected, initialization is necessary.
If any of the following operations are performed, initialization is necessary as well as when battery negative
terminal is disconnected.
• Power supply to the power window control unit is cut off by the removal f battery terminal or the battery fuse

is blown.

• Disconnection and connection of power window control unit harness connector.
• Removal and installation of motor from regulator assembly.
• Operation of regulator assembly as an independent unit.
• Removal and installation of rear power window control unit.
• Removal and installation of door glass.
• Removal and installation of door glass run.
The operations as per the following cannot be performed while initialization is not complete.
• AUTO-UP operation
• Anti-pinch function
• Door key cylinder switch power window function

ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement

INFOID:0000000005513310

INITIALIZATION PROCEDURE

1.

Disconnect battery negative terminal or power window control unit connector. Reconnect it after a minute
or more. 

2.

Turn ignition switch ON.

3.

Operate power window switch to fully open door glass. (This operation is unnecessary if door glass is
already fully open.)

4.

Pull and hold power window switch UP (AUTO-UP operation). Even after door glass stops at the fully
closed position, pull the switch for 2 seconds or more. 

5.

Initialization procedure is complete.

6.

Inspect anti-pinch function.

CHECK ANTI-PINCH FUNCTION

1.

Fully open door glass.

2.

Place a piece of wood near the fully closed position.

3.

Close door glass completely using AUTO-UP.

• Check that door glass lowers approximately 150 mm (5.9 in) without pinching piece of wood and stops.
• Check that door glass does not rise when operating power window main switch while lowering.

CAUTION:

• Perform initialization when AUTO-UP operation or anti-pinch function does not operate normally.
• Check that AUTO-UP operates before inspection when initialization is performed.
• Never check with hands or other body parts because they may be pinched. Never get pinched.
• It may switch to the fail-safe mode if open/close operation is performed continuously without fully

closing door glass. Perform initialization in the above situation. Refer to 

PWC-90, "Fail Safe"

.

• Finish initialization. Otherwise, the next operation cannot be done.
1.

AUTO-UP operation

2.

Anti-pinch function

3.

Door key cylinder switch power window function

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description

INFOID:0000000005513311

When the control unit is replaced, initialization is necessary.
If any of the following operations are performed, initialization is necessary as well as when the control unit is
disconnected.

PWC-6

< BASIC INSPECTION >

INSPECTION AND ADJUSTMENT

• Power supply to the power window control unit is cut off by the removal of battery terminal or the battery fuse

is blown.

• Disconnection and connection of power window control unit harness connector.
• Removal and installation of motor from regulator assembly.
• Disconnection and connection of battery negative terminal.
• Removal and installation of rear power window control unit.
• Removal and installation of door glass.
• Removal and installation of door glass run.
The following specified operations cannot be performed while initialization is not complete.
• AUTO-UP operation
• Anti-pinch function
• Door key cylinder switch power window function

ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement

INFOID:0000000005513312

INITIALIZATION PROCEDURE

1.

Disconnect battery negative terminal or power window control unit connector. Reconnect it after a minute
or more. 

2.

Turn ignition switch ON.

3.

Operate power window switch to fully open door glass. (This operation is unnecessary if door glass is
already fully open.)

4.

Pull and hold power window switch UP (AUTO-UP operation). Even after door glass stops at the fully
closed position, pull the switch for 2 seconds or more. 

5.

Initialization procedure is complete.

6.

Inspect anti-pinch function.

CHECK ANTI-PINCH FUNCTION

1.

Fully open door glass.

2.

Place a piece of wood near the fully closed position.

3.

Close door glass completely using AUTO-UP.

• Check that door glass lowers approximately 150 mm (5.9 in) without pinching piece of wood and stops.
• Check that door glass does not rise when operating power window main switch while lowering.

CAUTION:

• Perform initialization when AUTO-UP operation or anti-pinch function does not operate normally.
• Check that AUTO-UP operates before inspection when initialization is performed.
• Never check with hands or other body parts because they may be pinched. Never get pinched.
• It may switch to the fail-safe mode if open/close operation is performed continuously without fully

closing. Perform initialization in the above situation. Refer to 

PWC-90, "Fail Safe"

.

• Finish initialization. Otherwise, the next operation cannot be done.
1.

AUTO-UP operation

2.

Anti-pinch function

3.

Door key cylinder switch power window function

 

 

 

 

 

 

 

содержание   ..  1125  1126  1127  1128   ..