Nissan Murano Z51. Manual - part 1014

MIR-12

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-210, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check door mirror remote control switch (mirror switch).
Refer to 

MIR-12, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (mirror switch). Refer to 

MIR-75, "Removal and Instal-

lation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

MIRROR SWITCH : Component Inspection

INFOID:0000000005513404

1.

CHECK MIRROR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit Door 

mirror 

remote control switch 

Continuity 

Connector

Terminal

Connector

Terminal

M75

3

D14

15

Existed

4

13

15

12

16

4

Automatic drive positioner control unit 

Ground

Continuity 

Connector

Terminal

M75

3

Not existed

4

15

16

Door mirror remote control switch

Ground

Continuity

 Connector

Terminal

D14

7

Existed

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-13

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-75, "Removal and Installation"

.

CHANGEOVER SWITCH

CHANGEOVER SWITCH : Description

INFOID:0000000005513405

Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.

CHANGEOVER SWITCH : Component Function Check

INFOID:0000000005513406

1.

CHECK CHANGEOVER SWITCH FUNCTION

Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.

Is the inspection result normal?

YES

>> Changeover switch function is OK.

NO

>> Refer to 

MIR-13, "CHANGEOVER SWITCH : Diagnosis Procedure"

.

CHANGEOVER SWITCH : Diagnosis Procedure

INFOID:0000000005513407

1.

CHECK CHANGEOVER SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CHANGEOVER SWITCH CIRCUIT

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

4

7

Mirror switch

RIGHT

Existed

Other than above

Not existed

13

LEFT

Existed

Other than above

Not existed

15

UP

Existed

Other than above

Not existed

12

DOWN

Existed

Other than above

Not existed

Monitor item

Condition

MIR CHNG SW-R/L

When operating the changeover toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch

 Connector

Terminal

D14

10

Ground

5

11

MIR-14

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-210, "Removal and Installation"

 .

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CHANGEOVER SWITCH

Check door mirror remote control switch (changeover switch).
Refer to 

MIR-14, "CHANGEOVER SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (changeover switch). Refer to 

MIR-75, "Removal and

Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-39, "Intermittent Incident"

.

>> INSPECTION END

CHANGEOVER SWITCH : Component Inspection

INFOID:0000000005513408

1.

CHECK CHANGEOVER SWITCH 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit Door 

mirror 

remote control switch

Continuity

Connector

Terminal

Connector

Terminal

M75

2

D14

11

Existed

14

10

Automatic drive positioner control unit 

Ground

Continuity

Connector

Terminal

M75

2

Not existed

14

Door mirror remote control switch 

Ground

Continuity

Connector

Terminal

D14

7

Existed

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-15

< DTC/CIRCUIT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-75, "Removal and Installation"

.

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

10

7

Changeover switch

LEFT

Existed

Other than above

Not existed

11

RIGHT

Existed

Other than above

Not existed