Nissan Murano Z51. Manual - part 50

ADP-192

< ECU DIAGNOSIS INFORMATION >

BCM (BODY CONTROL MODULE)

DTC Index

INFOID:0000000005681380

NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to

BCS-17, "COM-

MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)"

• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1734: CONTROL UNIT

• B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA

Priority

DTC

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

No DTC is detected.
further testing
may be required.

—

U1000: CAN COMM

—

BCS-38

U1010: CONTROL UNIT(CAN)

—

BCS-39

U0415: VEHICLE SPEED SIG

—

BCS-40

B2013: ID DISCORD BCM-S/L*

—

SEC-51

B2014: CHAIN OF S/L-BCM*

—

SEC-52

B2190: NATS ANTENNA AMP

—

SEC-43

B2191: DIFFERENCE OF KEY

—

SEC-46

B2192: ID DISCORD BCM-ECM

—

SEC-47

B2193: CHAIN OF BCM-ECM

—

SEC-49

B2195: ANTI SCANNING

—

SEC-50

B2553: IGNITION RELAY

—

PCS-48

B2555: STOP LAMP

—

SEC-55

B2556: PUSH-BTN IGN SW

—

SEC-57

B2557: VEHICLE SPEED

—

SEC-59

B2560: STARTER CONT RELAY

—

SEC-60

B2562: LOW VOLTAGE

—

BCS-41

B2601: SHIFT POSITION

—

SEC-61

B2602: SHIFT POSITION

—

SEC-64

B2603: SHIFT POSI STATUS

—

SEC-66

B2604: PNP SW

—

SEC-69

BCM (BODY CONTROL MODULE)

ADP-193

< ECU DIAGNOSIS INFORMATION >

ADP

NOTE:

*: For models without steering lock unit this DTC is not applied.

B2605: PNP SW

—

SEC-71

B2606: S/L RELAY*

—

SEC-73

B2607: S/L RELAY*

—

SEC-74

B2608: STARTER RELAY

—

SEC-76

B2609: S/L STATUS*

—

SEC-78

B260A: IGNITION RELAY

—

PCS-50

B260B: STEERING LOCK UNIT*

—

SEC-82

B260C: STEERING LOCK UNIT*

—

SEC-83

B260D: STEERING LOCK UNIT*

—

SEC-84

B260F: ENG STATE SIG LOST

—

SEC-85

B2612: S/L STATUS*

—

SEC-88

B2614: ACC RELAY CIRC

—

PCS-52

B2615: BLOWER RELAY CIRC

—

PCS-55

B2616: IGN RELAY CIRC

—

PCS-58

B2617: STARTER RELAY CIRC

—

SEC-92

B2618: BCM

—

PCS-61

B2619: BCM*

—

SEC-94

B261A: PUSH-BTN IGN SW

—

SEC-95

B261E: VEHICLE TYPE

(Turn ON for 15

seconds)

—

SEC-98

B2622: INSIDE ANTENNA

—

DLK-91

B2623: INSIDE ANTENNA

—

DLK-93

B26E9: S/L STATUS*

(Turn ON for 15

seconds)

—

SEC-86

B26EA: KEY REGISTRATION

—

(Turn ON for 15

seconds)

—

SEC-87

C1704: LOW PRESSURE FL

—

WT-25

C1705: LOW PRESSURE FR

—

C1706: LOW PRESSURE RR

—

C1707: LOW PRESSURE RL

—

C1708: [NO DATA] FL

—

WT-27

C1709: [NO DATA] FR

—

C1710: [NO DATA] RR

—

C1711: [NO DATA] RL

—

C1716: [PRESSDATA ERR] FL

—

WT-30

C1717: [PRESSDATA ERR] FR

—

C1718: [PRESSDATA ERR] RR

—

C1719: [PRESSDATA ERR] RL

—

C1729: VHCL SPEED SIG ERR

—

WT-32

C1734: CONTROL UNIT

—

WT-34

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

ADP-194

< SYMPTOM DIAGNOSIS >

ADP SYSTEM SYMPTOMS

SYMPTOM DIAGNOSIS

ADP SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000005515426

The diagnostics item numbers show the sequence for inspection. Inspection in order from item 1.

Order

Function

Operation procedure

Symptom

Diagnostic item

Reference

page

Memory function

Perform memory storage
(Refer to

ADP-10

.) and

memory operation (Refer to

ADP-22

All parts do not operate in memory
function.

—

ADP-195

Memory indicator 1 or 2 does not oper-
ate.

—

ADP-196

Manual function

Perform manual function
(Refer to

ADP-18

All components of power seat do not
operate.

—

ADP-197

All components of tilt&telescopic do not
operate.

—

ADP-205

Manual function
and
memory function

Perform manual function
(Refer to

ADP-18

.) and

memory function (Refer to

ADP-22

.).

Manual function or memory function
does not operate. (for specific part)

Sliding

Reclining

Lifting (front)

Lifting (rear)

Steering tilt

Steering telescopic

Door mirror

Entry/exit assist
function

Perform entry/exit assist
function.
Exit assist function: Refer
to

ADP-26

Entry assist function: Refer
to

ADP-30

Entry/exit assist function does not op-
erate.

—

ADP-203

Intelligent Key in-
ter lock function

Perform Intelligent Key in-
ter lock function (Refer to

ADP-34

Intelligent Key inter lock function does
not operate.

—

ADP-204

ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION

ADP-195

< SYMPTOM DIAGNOSIS >

ADP

ALL PARTS DO NOT OPERATE IN MEMORY FUNCTION

Diagnosis Procedure

INFOID:0000000005515427

CHECK MEMORY FUNCTION

Check memory function.
Refer to

ADP-22, "MEMORY FUNCTION : System Description"

Is the inspection result normal?

YES

>> Memory function is normal.

>> GO TO 2.

CHECK SEAT MEMORY SWITCH

Check seat memory switch.
Refer to

ADP-66, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunction parts.

CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check driver seat control unit power supply and ground circuit.
Refer to

ADP-52, "DRIVER SEAT CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunction parts.

CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check automatic drive positioner control unit power supply and ground circuit.
Refer to

ADP-52, "AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunction parts.

PERFORM INITIALIZATION AND MEMORY STORING PROCEDURE

Perform initialization procedure.
Refer to

ADP-9, "SYSTEM INITIALIZATION : Special Repair Requirement"

Perform memory storing procedure.
Refer to

ADP-10, "MEMORY STORING : Special Repair Requirement"

Check memory function.
Refer to

ADP-22, "MEMORY FUNCTION : System Description"

Is the inspection result normal?

YES

>> Memory function is normal.

>> GO TO 6.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

GI-39, "Intermittent Incident"

>> GO TO 1.

содержание .. 48 49 50 51 ..