Murano Cross Cabriolet Z51 (2013 year). Manual - part 81

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

SEC-105

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

VEHICLE SECURITY ALARM DOES NOT ACTIVATE

Description

INFOID:0000000008460597

Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.

CONDITION OF VEHICLE (OPERATING CONDITION)

• “ENGINE START BY I-KEY” setting: ON

Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.

Diagnosis Procedure

INFOID:0000000008460598

1.

CHECK DOOR SWITCH

Check door switch.
Refer to 

DLK-55, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the malfunctioning door switch. Refer to 

DLK-55, "Diagnosis Procedure"

.

2.

CHECK TRUNK ROOM LAMP SWITCH

Check trunk room lamp switch circuit.
Refer to 

DLK-69, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

3.

CHECK HEADLAMP FUNCTION

Check headlamp function.
Refer to 

SEC-93, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK HORN FUNCTION

Check horn function. Refer to 

SEC-94, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-106

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE

INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE

Description

INFOID:0000000008460599

Intelligent Key insert information does not operate when push-button ignition switch is operated while Intelli-
gent Key is not inside vehicle.
NOTE:
Operating conditions of warning function are extremely complicated. Refer to 

DLK-23, "WARNING FUNC-

TION : System Description"

.

Diagnosis Procedure

INFOID:0000000008460600

1.

CHECK POWER POSITION

Check if ignition switch position is changing or not.
Does ignition switch position change?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK PUSH-BUTTON IGNITION SWITCH

Check push-button ignition switch.
Refer to 

PCS-65, "Component Function Check"

.

Is the inspection result normal?

YES

>> Check BCM for DTC. Refer to 

BCS-55, "DTC Index"

.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK DOOR SWITCH

Check door switch.
Refer to 

DLK-55, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK KEY SLOT

Check key slot.
Refer to 

DLK-91, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INFORMATION DISPLAY

Check information display.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK KEY SLOT INDICATOR

Check key slot indicator.
Refer to 

DLK-93, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

Revision: 2012 October

2013 Murano CrossCabriolet

INTELLIGENT KEY INSERT INFORMATION DOES NOT OPERATE

SEC-107

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

NO

>> GO TO 1.

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-108

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

PANIC ALARM FUNCTION DOES NOT OPERATE

PANIC ALARM FUNCTION DOES NOT OPERATE

Description

INFOID:0000000008460601

NOTE:
• Before performing the following procedure, check “Work Flow”. Refer to 

SEC-37, "Work Flow"

.

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATION CONDITIONS)

• Power supply position: OFF or LOCK
• PANIC ALARM SET: MODE 1

Check the setting of “PANIC ALARM SET” in “Work Support” mode of “INTELLIGENT KEY” of “BCM” using
CONSULT.

Diagnosis Procedure

INFOID:0000000008460602

1.

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function. Refer to 

DLK-20, "REMOTE KEYLESS ENTRY FUNCTION : System

Description"

.

Does door lock or unlock when operating Intelligent key button?

YES

>> GO TO 2.

NO

>> Go to 

DLK-104, "Diagnosis Procedure"

.

2.

CHECK VEHICLE SECURITY ALARM OPERATION

Check vehicle security alarm operation. Refer to 

SEC-16, "VEHICLE SECURITY SYSTEM : System Descrip-

tion"

.

Is alarm (headlamps and horns) activated?

YES

>> GO TO 3.

NO

>> Go to 

SEC-105, "Diagnosis Procedure"

.

3.

CHECK “PANIC ALARM” BUTTON OPERATION

1.

Turn ignition switch ON.

2.

Select “RKE-PANIC” and “RKE OPE COUN1” in “Data Monitor” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT.

3.

Check “RKE-PANIC” and “RKE OPE COUN1” indications when pressing (for approximately 0.5 seconds)
“PANIC ALARM” button of Intelligent Key.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace Intelligent Key.

4.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> GO TO 1.

Indication

Specification

RKE-PANIC

OFF 

→

 ON

RKE OPE COUN1

Increases

Revision: 2012 October

2013 Murano CrossCabriolet

KEY SLOT

SEC-109

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

REMOVAL AND INSTALLATION

KEY SLOT

Exploded View

INFOID:0000000008460603

Removal and Installation

INFOID:0000000008460604

REMOVAL

1.

Remove the instrument lower panel LH (2). Refer to 

IP-13,

"Removal and Installation"

.

2.

Disconnect key slot connector.

3.

Remove the key slot mounting screw (A), and then remove key
slot (1) from instrument lower panel LH (2).

INSTALLATION

Install in the reverse order of removal.

1.

Key slot

2.

Instrument lower panel LH

JMKIA1820ZZ

JMKIA1821ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-110

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

PUSH-BUTTON IGNITION SWITCH

PUSH-BUTTON IGNITION SWITCH

Exploded View

INFOID:0000000008460605

Removal and Installation

INFOID:0000000008460606

REMOVAL

1.

Remove the instrument stay cover LH. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove the push-button ignition switch (1) from instrument stay
cover LH, after removing pawl (A). Press push-button ignition
switch (1) back to disengage from instrument stay cover LH (2).

INSTALLATION

Install in the reverse order of removal.

1.

Push-button ignition switch

JMKIA1812ZZ

JMKIA1813ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

SECURITY INDICATOR LAMP

SEC-111

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

SECURITY INDICATOR LAMP

Exploded View

INFOID:0000000008460607

Removal and Installation

INFOID:0000000008460608

REMOVAL

Remove the security indicator lamp (1).

•

Disengage pawls with remover tool (A) and pull up the security
indicator lamp.

INSTALLATION

Install in the reverse order of removal.

1.

Security indicator lamp

JMKIA1830ZZ

: Pawl

JMKIA1831ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

SR-1

RESTRAINTS

C

D

E

F

G

I

J

K

L

M

SECTION 

SR

A

B

SR

N

O

P

CONTENTS

SRS AIRBAG

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

2

Service Procedure Precautions for Models with a 
Pop-up Roll Bar .........................................................

2

Precaution for Battery Service  ..................................

2

Occupant Classification System ..............................

2

Service ......................................................................

3

PREPARATION ............................................

4

PREPARATION ...................................................

4

Commercial Service Tools  ........................................

4

BASIC INSPECTION  ....................................

5

COLLISION DIAGNOSIS  ....................................

5

FOR FRONTAL COLLISION  .......................................

5

FOR FRONTAL COLLISION : When SRS is acti-
vated in a collision .....................................................

5

FOR FRONTAL COLLISION : When SRS is not 
activated in a collision  ...............................................

6

FOR SIDE AND ROLLOVER COLLISION  ..................

7

FOR SIDE AND ROLLOVER COLLISION : When 
SRS is activated in a collision  ...................................

7

FOR SIDE AND ROLLOVER COLLISION : When 
SRS is not activated in a collision  .............................

8

REMOVAL AND INSTALLATION ...............

11

DRIVER AIR BAG MODULE ..............................

11

Exploded View  ........................................................

11

Removal and Installation  .........................................

11

SPIRAL CABLE  ................................................

14

Exploded View .........................................................

14

Removal and Installation  .........................................

14

FRONT PASSENGER AIR BAG MODULE  ......

17

Exploded View .........................................................

17

Removal and Installation  .........................................

17

DOOR-MOUNTED CURTAIN AIR BAG MOD-
ULE ....................................................................

19

Exploded View .........................................................

19

Removal and Installation  .........................................

19

POP-UP ROLL BAR  .........................................

21

Exploded View .........................................................

21

Removal and Installation  .........................................

21

CRASH ZONE SENSOR ...................................

26

Exploded View .........................................................

26

Removal and Installation  .........................................

26

SATELLITE SENSOR  .......................................

28

Exploded View .........................................................

28

Removal and Installation  .........................................

28

DIAGNOSIS SENSOR UNIT  .............................

30

Exploded View .........................................................

30

Removal and Installation  .........................................

30

FRONT SEAT BELT PRE-TENSIONER  ...........

32

Removal and Installation  .........................................

32

OCCUPANT CLASSIFICATION SYSTEM 
CONTROL UNIT ................................................

33

Removal and Installation  .........................................

33

Revision: 2012 October

2013 Murano CrossCabriolet

SR-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000008462927

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service Procedure Precautions for Models with a Pop-up Roll Bar

INFOID:0000000008462928

WARNING:

Always observe the following items for preventing accidental activation.
• Risk of passenger injury or death may increase if the pop-up roll bar does not deploy during a roll

over collision. In order to reduce the chance of an incident where the pop-up roll bar is inoperative,
all maintenance must be performed by a NISSAN or INFINITI dealer.

• Before removing and installing the pop-up roll bar component parts and harness, always turn the

ignition switch OFF, disconnect the battery negative terminal, and wait for 3 minutes or more. (The
purpose of this operation is to discharge electricity that is accumulated in the auxiliary power supply
circuit in the air bag diagnosis sensor unit.)

• When repairing, removing, and installing a pop-up roll bar, always refer to SRS AIR BAG and SRS

AIR BAG CONTROL warnings in the Service Manual.

Precaution for Battery Service

INFOID:0000000008462929

Before disconnecting the battery, lower both the driver and passenger windows. This will prevent any interfer-
ence between the window edge and the vehicle when the door is opened/closed. During normal operation, the
window slightly raises and lowers automatically to prevent any window to vehicle interference. The automatic
window function will not work with the battery disconnected.

Occupant Classification System

INFOID:0000000008462930

• Replace occupant classification system control unit and passenger front seat cushion as an assembly.

Refer to 

SE-39, "Removal and Installation"

.

Revision: 2012 October

2013 Murano CrossCabriolet

PRECAUTIONS

SR-3

< PRECAUTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

Service

INFOID:0000000008462931

• Never use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes

or more.
For approximately 3 minutes or more after the cables are removed, it is still possible for the air bag and seat
belt pre-tensioner to deploy. Therefore, never work on any SRS connectors or wires until at least 3 minutes
have elapsed.

• Diagnosis sensor unit must always be installed with their arrow marks “

⇐

” pointing towards the front of the

vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.

• The spiral cable must be aligned in the neutral position since its rotations are limited. Never turn steering

wheel and column after removal of steering gear.

• Handle air bag module carefully. Always place driver and passenger air bag modules with the pad side fac-

ing upward and seat mounted side air bag module standing with the stud bolt side facing down.

• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following passenger air bag deployment.
• Never allow harness to come in contact with oil, grease, waste oil, or water.
• Never insert foreign materials, such as a screwdriver, into the harness connector. (This is to prevent acci-

dental activation caused by static electricity.)

• Never enter in the deployment area of pop-up roll bar. Never put an object in the deployment area of pop-up

roll bar. (This is to prevent an unintentional deployment.)

• When handling pop-up roll bar, always grip frame and handle carefully.
• Never reuse pop-up roll bar that is deployed once.
• Modification of pop-up roll bar may cause unintentional deployment or a malfunction. Never disassemble or

apply modification to the pop-up roll bar. (Non-disassembly)

• Never apply impact to pop-up roll bar by dropping or others. Always replace if an impact is applied.
• When repairing surrounding area of pop-up roll bar, be careful not to apply over voltage of welding and oth-

ers. Remove pop-up roll bar in advance if necessary. Be careful for modification of mounting area or installa-
tion of other parts because these may cause damage or a malfunction.

• Never disassemble the pop-up roll bar.
• Never expose the pop-up roll bar to temperatures exceeding 90 

°

C (194 

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the pop-up roll bar.

Revision: 2012 October

2013 Murano CrossCabriolet

SR-4

< PREPARATION >

PREPARATION

PREPARATION

PREPARATION

Commercial Service Tools

INFOID:0000000008462932

Tool name

Description

Tamper resistant TORX bit

Removes driver air bag module

Remover tool

Removes clips, pawls, and metal clip

S-NT757

JMKIA3050ZZ

Revision: 2012 October

2013 Murano CrossCabriolet

COLLISION DIAGNOSIS

SR-5

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

BASIC INSPECTION

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION

FOR FRONTAL COLLISION : When SRS is activated in a collision

INFOID:0000000008462933

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1.

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

2.

Replace the diagnosis sensor unit.

3.

Remove the front air bag modules, crash zone sensor, bracket and seat belt pre-tensioner assemblies.

4.

Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

5.

Install new front air bag modules, crash zone sensor assembly, bracket and seat belt pre-tensioner
assemblies.

6.

Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to 

SRC-13, "On Board Diagnosis

Function"

 or 

SRC-17, "CONSULT Function"

 for details. Ensure entire SRS operates properly.

7.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-13, "On Board Diagnosis Function"

 or 

SRC-17, "CONSULT Function"

.

SRS INSPECTION (FOR FRONTAL COLLISION)

Part

Inspection

Driver air bag module

If the driver air bag has deployed:
REPLACE
Install with new fasteners.

Front passenger air bag module 
(if equipped)

If the front passenger air bag has deployed:
REPLACE
Install with new fasteners.

Crash zone sensor

If any of the front air bags or seat belt pre-tensioners* have been activated:
REPLACE the crash zone sensor and bracket with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Diagnosis sensor unit

If any of the SRS components have been activated:
REPLACE the diagnosis sensor unit.
Install with new fasteners.

Steering wheel

1.

Visually check steering wheel for deformities.

2.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

3.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

4.

Check steering wheel for excessive free play.

5.

If no damage is found, reinstall.

6.

If damaged 

−

 REPLACE.

Spiral cable

If the driver front air bag has deployed:
REPLACE the spiral cable.

Occupant classification system 
(Passenger seat)

1.

Remove passenger seat assembly.

2.

Check control unit case for dents, cracks of deformities.

3.

Check connectors and pressure sensor tube for damage, and terminals for deformities.

4.

Check seat frame and cushion pan for dents or deformities.

5.

If no damage is found, reinstall seat with new fasteners.

6.

If damaged 

−

 REPLACE seat cushion assembly with new fasteners.

Revision: 2012 October

2013 Murano CrossCabriolet

SR-6

< BASIC INSPECTION >

COLLISION DIAGNOSIS

FOR FRONTAL COLLISION : When SRS is not activated in a collision

INFOID:0000000008462934

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1.

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

2.

Check the SRS components using the table below:
Replace any SRS components showing visible signs of damage. (dents, cracks and deformation, etc.)

3.

Perform self-diagnosis using CONSULT or air bag warning lamp. Refer to 

SRC-13, "On Board Diagnosis

Function"

 or 

SRC-17, "CONSULT Function"

 for details. Ensure entire SRS operates properly.

4.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-13, "On Board Diagnosis Function"

 or 

SRC-17, "CONSULT Function"

.

SRS INSPECTION (FOR FRONTAL COLLISION)

Harness and connectors

1.

Check connectors for poor connection, damage, and terminals for deformities.

2.

Check harness for binding, chafing, cuts, or deformities.

3.

If no damage is found, reinstall the harness and connectors.

4.

If damaged 

−

 REPLACE the damaged harness. Do not attempt to repair, splice or modify any 

SRS harness.

Instrument panel assembly

If the front passenger air bag has deployed: 
REPLACE the instrument panel assembly. (integrated type)

Part

Inspection

Part

Inspection

Driver air bag module

If the driver air bag has NOT been deployed:
1.

Remove driver air bag module. Check harness cover and connectors for damage, terminals for 
deformities, and harness for binding.

2.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged 

−

 REPLACE. Install driver air bag module with new fasteners.

Front passenger air bag module 
(if equipped)

If the front passenger air bag has NOT been deployed:
1.

Remove front passenger air bag module. Check harness cover and connectors for damage, ter-
minals for deformities, and harness for binding.

2.

Install front passenger air bag module into the instrument panel to check fit with the instrument 
panel.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged 

−

 REPLACE. Install front passenger air bag modules with new fasteners.

Crash zone sensor

If the front air bags or seat belt pre-tensioners have NOT been activated:
1.

Remove the crash zone sensor. Check harness connectors for damage, terminals for deformi-
ties, and harness for binding.

2.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the crash zone sensor 
and bracket.

3.

Install the crash zone sensor to check fit.

4.

If no damage is found, reinstall with new fasteners.

5.

If damaged 

−

 REPLACE the crash zone sensor and bracket with new fasteners. 

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If the pre-tensioners have NOT been activated:
1.

Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for 
binding.

2.

Check belts for damage and anchors for loose mounting.

3.

Check retractor for smooth operation.

4.

Check seat belt adjuster for damage.

5.

Check for deformities of the center pillar inner.

6.

If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

7.

If no damage is found, reinstall seat belt pre-tensioner assembly.

8.

If damaged 

−

 REPLACE. Install the seat belt pre-tensioners with new fasteners. 

Revision: 2012 October

2013 Murano CrossCabriolet

COLLISION DIAGNOSIS

SR-7

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

FOR SIDE AND ROLLOVER COLLISION

FOR SIDE AND ROLLOVER COLLISION : When SRS is activated in a collision

INFOID:0000000008462935

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1.

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

2.

Replace the following components:
• Front seat back assembly (on the side on which side air bag is activated)
• Door finisher (on the side on which door-mounted curtain air bag is activated)
• Pop-up roll bar assemblies and pop-up roll bar covers
• Side air bag (satellite) sensor LH/RH (on the side on which side air bag is activated)
• Diagnosis sensor unit
• Seat belt pre-tensioner assemblies

3.

Check the SRS components and the related parts using the following table.
Replace any SRS components and the related parts showing visible signs of damage. (dents, cracks,
deformation, etc.)

4.

Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to 

SRC-13, "On Board Diag-

nosis Function"

 or 

SRC-17, "CONSULT Function"

 for details. Make sure entire SRS operates properly.

5.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-13, "On Board Diagnosis Function"

 or 

SRC-17, "CONSULT Function"

.

Diagnosis sensor unit

If none of the SRS components have been activated:
1.

Check case for dents, cracks or deformities.

2.

Check connectors for damage, and terminals for deformities.

3.

If no damage is found, reinstall with new fasteners.

4.

If damaged 

−

 REPLACE. Install diagnosis sensor unit with new fasteners.

Steering wheel

1.

Visually check steering wheel for deformities.

2.

Check harness (built into steering wheel) and connectors for damage, and terminals for defor-
mities.

3.

Install driver air bag module into the steering wheel to check fit and alignment with the wheel.

4.

Check steering wheel for excessive free play.

5.

If no damage is found, reinstall.

6.

If damaged 

−

 REPLACE.

Spiral cable

If the driver front air bag has not deployed:
1.

Visually check spiral cable and combination switch for damage.

2.

Check connectors and protective tape for damage.

3.

Check steering wheel for noise, binding or heavy operation.

4.

If no damage is found, reinstall.

5.

If damaged 

−

 REPLACE.

Occupant classification system 
(Passenger seat)

1.

Remove passenger seat assembly.

2.

Check control unit case for dents, cracks of deformities.

3.

Check connectors and pressure sensor tube for damage, and terminals for deformities.

4.

Check seat frame and cushion pan for dents or deformities.

5.

If no damage is found, reinstall seat with new fasteners.

6.

If damaged 

−

 REPLACE seat cushion assembly with new fasteners.

Harness and connectors

1.

Check connectors for poor connection, damage, and terminals for deformities.

2.

Check harness for binding, chafing, cuts, or deformities.

3.

If no damage is found, reinstall the harness and connectors.

4.

If damaged 

−

 REPLACE the damaged harness. Do not attempt to repair, splice or modify any 

SRS harness.

Instrument panel assembly

If the front passenger air bag has NOT deployed:
1.

Visually check instrument panel assembly for damage.

2.

If no damage is found, reinstall the instrument panel assembly.

3.

If damaged 

−

 REPLACE the instrument panel assembly.

Part

Inspection

Revision: 2012 October

2013 Murano CrossCabriolet

SR-8

< BASIC INSPECTION >

COLLISION DIAGNOSIS

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

FOR SIDE AND ROLLOVER COLLISION : When SRS is not activated in a collision

INFOID:0000000008462936

CAUTION:

Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles.

WORK PROCEDURE

1.

Before performing any of the following steps, ensure that all vehicle body and structural repairs have been
completed.

2.

Check the SRS components and the related parts using the following table.
• If the front seat back assembly is damaged, the front seat back assembly must be replaced.
• If the door finisher assembly is damaged, the door finisher assembly and door-mounted curtain air bag

module must be replaced.

3.

Perform self-diagnosis using CONSULT and “AIR BAG” warning lamp. Refer to 

SRC-17, "CONSULT

Function"

 for details. Make sure entire SRS operates properly.

4.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to

SRC-17, "CONSULT Function"

.

SRS INSPECTION (FOR SIDE AND ROLLOVER COLLISION)

Part

Inspection

Side curtain air bag module LH

If the side curtain air bag LH has deployed:
REPLACE the side curtain air bag module LH.
Install with new fasteners.

Side curtain air bag module RH

If the side curtain air bag RH has deployed:
REPLACE the side curtain air bag module RH.
Install with new fasteners.

Front side air bag module LH

If the front side air bag LH has deployed: 
REPLACE front seatback assembly LH.

Front side air bag module RH

If the front side air bag RH has deployed:
REPLACE front seatback assembly RH.

Side air bag (satellite) sensor 
(LH or RH) 

If any of the SRS components have deployed:
REPLACE the side air bag (satellite) sensor on the collision side with new fasteners.

Diagnosis sensor unit

If any of the SRS components have deployed:
REPLACE the diagnosis sensor unit with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If either the driver or passenger seat belt pre-tensioner* has been activated:
REPLACE all seat belt pre-tensioner assemblies with new fasteners.
*: Confirm seat belt pre-tensioner activation using CONSULT only.

Center inner pillar

1.

Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).

2.

If damaged 

−

 REPAIR the center inner pillar.

Trim/headlining

1.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the interior trim on the 
collision side.

2.

If damaged 

−

 REPLACE the damaged trim parts.

Door-mounted curtain air bag 
module LH

If the door-mounted curtain air bag module LH has deployed:
REPLACE the door finisher LH and door-mounted curtain air bag module.
Install with new fasteners.

Door-mounted curtain air bag 
module RH

If the door-mounted curtain air bag module RH has deployed:
REPLACE the door finisher RH and door-mounted curtain air bag module.
Install with new fasteners.

Pop-up roll bar assemblies

If the pop-up roll bar has deployed:
REPLACE pop-up roll bar assemblies and pop-up roll bar covers.
Install with new fasteners.

Revision: 2012 October

2013 Murano CrossCabriolet

COLLISION DIAGNOSIS

SR-9

< BASIC INSPECTION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

Part

Inspection

Side curtain air bag module LH

If the side curtain air bag LH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.

2.

If damaged 

−

 Remove the side curtain air bag module LH.

3.

Check for visible signs of damage (tears etc.) of the side curtain air bag module LH.

4.

Check harness and connectors for damage, and terminals for deformities.

5.

If no damage is found, reinstall the side curtain air bag module LH with new fasteners.

6.

If damaged 

−

 REPLACE the side curtain air bag module LH with new fasteners. 

Side curtain air bag module RH

If the side curtain air bag RH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the center pillar on the col-
lision side.

2.

If damaged 

−

 Remove the side curtain air bag module RH.

3.

Check for visible signs of damage (tears etc.) of the side curtain air bag module RH.

4.

Check harness and connectors for damage, and terminals for deformities.

5.

If no damage is found, reinstall the side curtain air bag module RH with new fasteners.

6.

If damaged 

−

 REPLACE the side curtain air bag module RH with new fasteners. 

Front side air bag module LH

If the front side air bag LH has NOT deployed: 
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.

2.

Check harness and connectors for damage, and terminals for deformities.

3.

If damaged 

−

 REPLACE the front seatback assembly LH. 

Front side air bag module RH

If the front side air bag RH has NOT deployed:
1.

Check for visible signs of damage (dents, tears, deformation, etc.) of the seat back on the col-
lision side.

2.

Check harness and connectors for damage, and terminals for deformities.

3.

If damaged 

−

 REPLACE the front seatback assembly RH. 

Side air bag (satellite) sensor 
(LH or RH) 

If none of the SRS components have been activated:
1.

Remove the side air bag (satellite) sensor (LH or RH) on the collision side. Check harness con-
nectors for damage, terminals for deformities, and harness for binding.

2.

Check for visible signs of damage (dents, cracks, deformation, etc.) of the side air bag (satellite) 
sensor (LH or RH).

3.

Install the side air bag (satellite) sensor (LH or RH) to check fit.

4.

If no damage is found, reinstall the side sir bag (satellite) sensor (LH or RH) with new fasteners.

5.

If damaged 

−

 REPLACE the side air bag (satellite) sensor (LH or RH) with new fasteners.

Diagnosis sensor unit

If none of the SRS components have been activated:
1.

Check case and bracket for dents, cracks or deformities.

2.

Check connectors for damage, and terminals for deformities.

3.

If no damage is found, reinstall the diagnosis sensor unit with new fasteners.

4.

If damaged 

−

 REPLACE the diagnosis sensor unit with new fasteners.

Seat belt pre-tensioner assem-
blies
(All applicable locations: buckle, 
retractor, lap outer)

If the pre-tensioners have NOT been activated:
1.

Remove seat belt pre-tensioners.
Check harness cover and connectors for damage, terminals for deformities, and harness for 
binding.

2.

Check belts for damage and anchors for loose mounting.

3.

Check retractor for smooth operation.

4.

Check seat belt adjuster for damage.

5.

Check for deformities of the center pillar inner.

6.

If the center pillar inner has no damage, REPLACE the seat belt pre-tensioner assembly.

7.

If no damage is found, reinstall seat belt pre-tensioner assembly.

8.

If damaged 

−

 REPLACE. Install the seat belt pre-tensioners with new fasteners. 

Seat (with front side air bag)

If the front LH or front RH side air bag modules have NOT deployed: 
1.

Visually check the seat on the collision side.

2.

Remove the seat on the collision side and check the following for damage and deformities.

-

Harness, connectors and terminals

-

Frame and recliner (for front and rear seat), and also adjuster and slides (for front seat)

3.

If no damage is found, reinstall the seat.

4.

If damaged 

−

 REPLACE the damaged seat parts using new fasteners. If the front seat back is 

damaged, the front seat back assembly must be replaced.

Center inner pillar

1.

Check the center inner pillar on the collision side for damage (dents, cracks, deformation, etc.).

2.

If damaged 

−

 REPAIR the center inner pillar.

Revision: 2012 October

2013 Murano CrossCabriolet