Murano Cross Cabriolet Z51 (2013 year). Manual - part 77

SEC-42, "Diagnosis Procedure"

>> GO TO 3.

WRITING VEHICLE SPECIFICATION

CONSULT Configuration

Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to

BCS-63, "Work Procedure"

>> GO TO 4.

INITIALIZE BCM (NATS) (IF EQUIPPED)

Perform BCM initialization. (NATS)

>> WORK END

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-42

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1610 LOCK MODE

DTC/CIRCUIT DIAGNOSIS

P1610 LOCK MODE

Description

INFOID:0000000008460505

When the starting operation is carried more than five times consecutively under the following conditions, NATS
will shift to the mode which prevents the engine from being started.
• Unregistered Intelligent Key is used.
• BCM or ECM is malfunctioning.

DTC Logic

INFOID:0000000008460506

DTC DETECTION LOGIC

NOTE:
If DTC P1610 is displayed with other DTC (for BCM or ENGINE), first perform the trouble diagnosis for other
DTC.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “BCM” and “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460507

CHECK ENGINE START FUNCTION

Check that DTC except for DTC P1610 is not detected.
If detected, erase DTC after fixing.

Turn ignition switch OFF.

Insert Intelligent Key into key slot.

Turn ignition switch ON and wait 5 seconds.

Turn ignition switch OFF and wait 5 seconds.

Repeat steps 4 and 5 twice (a total of 3 times).

Check that engine can start.

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1610

LOCK MODE

When the starting operation is carried out 5 times or
more consecutively under the following conditions.
• Unregistered Intelligent Key
• BCM or ECM is malfunctioning.

—

Revision: 2012 October

2013 Murano CrossCabriolet

P1611 ID DISCORD, IMMU-ECM

SEC-43

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

P1611 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000008460508

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

SEC-43, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460509

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

CHECK SELF DIAGNOSTIC RESULT

Select “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Erase DTC.

Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to

SEC-43, "DTC Logic"

Is DTC detected

YES

>> GO TO 3.

>> INSPECTION END

REPLACE BCM

Replace BCM. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 4.

REPLACE ECM

Replace ECM. Refer to

SEC-44, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1611

ID DISCORD, IMMU-ECM

The ID verification result between BCM and ECM is NG.

• BCM
• ECM

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-44

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1612 CHAIN OF ECM-IMMU

P1612 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000008460510

DTC DETECTION LOGIC

NOTE:
• If DTC P1612 is displayed with DTC U1000 (BCM), first perform the trouble diagnosis for DTC U1000. Refer

BCS-66, "DTC Logic"

• If DTC P1612 is displayed with DTC U1010 (BCM), first perform the trouble diagnosis for DTC U1010. Refer

BCS-67, "DTC Logic"

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460511

REPLACE BCM

Replace BCM. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

REPLACE ECM

Replace ECM. Refer to

SEC-45, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1612

CHAIN OF ECM-IMMU

Inactive communication between ECM
and BCM

• Harness or connectors

(The CAN communication line is open or
shorted.)

• BCM
• ECM

Revision: 2012 October

2013 Murano CrossCabriolet

P1614 CHAIN OF IMMU-KEY

SEC-45

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

P1614 CHAIN OF IMMU-KEY

DTC Logic

INFOID:0000000008460512

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE 1

Insert Intelligent Key into key slot.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE 2

Press push-button ignition switch.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

SEC-45, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460513

INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?

DTC CONFIRMATION PROCEDURE 1>>GO TO 2.
DTC CONFIRMATION PROCEDURE 2>>GO TO 6.

CHECK PUSH-BUTTON IGNITION SWITCH OPERATION

Press push-button ignition switch and check if it turns ON.

Does ignition switch turn ON?

YES

>> GO TO 3.

>> GO TO 5.

CHECK KEY SLOT COMMUNICATION SIGNAL

Turn ignition switch OFF.

Disconnect key slot connector.

Check voltage between key slot harness connector and ground.

Is the inspection result normal?

YES

>> Replace key slot. Refer to

>> GO TO 4.

CHECK KEY SLOT COMMUNICATION SIGNAL CIRCUIT

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1614

CHAIN OF IMMU-KEY

Inactive communication between key
slot and BCM.

• Harness or connectors

(The key slot circuit is open or shorted.)

• Key slot
• BCM

(+)

(–)

Voltage (V)

(Approx.)

Key slot

Connector

Terminal

M99

Ground

Battery voltage

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-46

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1614 CHAIN OF IMMU-KEY

Disconnect BCM connector.

Check continuity between key slot harness connector and BCM harness connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK KEY SLOT GROUND CIRCUIT

Turn ignition switch OFF.

Disconnect key slot connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK KEY SLOT INPUT SIGNAL

Turn ignition switch OFF.

Disconnect key slot connector.

Check voltage between key slot harness connector and ground.

Is the inspection result normal?

YES

>> Replace key slot. Refer to

>> GO TO 7.

CHECK KEY SLOT CIRCUIT

Disconnect BCM connector.

Check continuity between key slot harness connector and BCM harness connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

Key slot

BCM

Continuity

Connector

Terminal

Connector

Terminal

M99

M122

Existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Not existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Existed

(+)

(–)

Voltage (V)

(Approx.)

Key slot

Connector

Terminal

M99

Ground

Battery voltage

Key slot

BCM

Continuity

Connector

Terminal

Connector

Terminal

M99

M122

Existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

P1614 CHAIN OF IMMU-KEY

SEC-47

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK INTERMITTENT INCIDENT

SEC-48, "Diagnosis Procedure"

>> INSPECTION END

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-48

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P1615 DIFFRENCE OF KEY

P1615 DIFFRENCE OF KEY

DTC Logic

INFOID:0000000008460514

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Press push-button ignition switch.

Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460515

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

REPLACE INTELLIGENT KEY

Replace Intelligent Key.

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 3.

CHECK INTERMITTENT INCIDENT

SEC-49, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

P1615

DIFFERENCE OF KEY

The ID verification result between BCM and
Intelligent Key is NG.

Intelligent Key

Revision: 2012 October

2013 Murano CrossCabriolet

B2190 NATS ANTENNA AMP.

SEC-49

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

B2190 NATS ANTENNA AMP.

DTC Logic

INFOID:0000000008460516

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE 1

Insert Intelligent Key into key slot.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Go to

>> GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE 2

Press push-button ignition switch.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Go to

SEC-49, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460517

INSPECTION START

Perform inspection in accordance with procedure that confirms DTC.
Which procedure confirms DTC?

DTC CONFIRMATION PROCEDURE 1>>GO TO 2.
DTC CONFIRMATION PROCEDURE 2>>GO TO 6.

CHECK PUSH-BUTTON IGNITION SWITCH OPERATION

Press push-button ignition switch and check if it turns ON.

Does ignition switch turn ON?

YES

>> GO TO 3.

>> GO TO 5.

CHECK KEY SLOT COMMUNICATION SIGNAL

Turn ignition switch OFF.

Disconnect key slot connector.

Check voltage between key slot harness connector and ground.

Is the inspection result normal?

YES

>> Replace key slot. Refer to

>> GO TO 4.

CHECK KEY SLOT COMMUNICATION SIGNAL CIRCUIT

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2190

NATS ANTENNA AMP

Inactive communication between key
slot and BCM.

• Harness or connectors

(The key slot circuit is open or shorted.)

• Key slot
• BCM

(+)

(–)

Voltage (V)

(Approx.)

Key slot

Connector

Terminal

M99

Ground

Battery voltage

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-50

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2190 NATS ANTENNA AMP.

Disconnect BCM connector.

Check continuity between key slot harness connector and BCM harness connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK KEY SLOT GROUND CIRCUIT

Turn ignition switch OFF.

Disconnect key slot connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK KEY SLOT INPUT SIGNAL

Turn ignition switch OFF.

Disconnect key slot connector.

Check voltage between key slot harness connector and ground.

Is the inspection result normal?

YES

>> Replace key slot. Refer to

>> GO TO 7.

CHECK KEY SLOT CIRCUIT

Disconnect BCM connector.

Check continuity between key slot harness connector and BCM harness connector.

Check continuity between key slot harness connector and ground.

Is the inspection result normal?

Key slot

BCM

Continuity

Connector

Terminal

Connector

Terminal

M99

M122

Existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Not existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Existed

(+)

(–)

Voltage (V)

(Approx.)

Key slot

Connector

Terminal

M99

Ground

Battery voltage

Key slot

BCM

Continuity

Connector

Terminal

Connector

Terminal

M99

M122

Existed

Key slot

Ground

Continuity

Connector

Terminal

M99

Not existed

Revision: 2012 October

2013 Murano CrossCabriolet

B2190 NATS ANTENNA AMP.

SEC-51

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

YES

>> GO TO 8.

>> Repair or replace harness or connector.

CHECK INTERMITTENT INCIDENT

SEC-52, "Diagnosis Procedure"

>> INSPECTION END

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-52

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2191 DIFFERENCE OF KEY

B2191 DIFFERENCE OF KEY

DTC Logic

INFOID:0000000008460518

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Press push-button ignition switch.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460519

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

REPLACE INTELLIGENT KEY

Replace Intelligent Key.

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 3.

CHECK INTERMITTENT INCIDENT

SEC-53, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2191

DIFFERENCE OF KEY

The ID verification result between BCM and
Intelligent Key is NG.

Intelligent Key

Revision: 2012 October

2013 Murano CrossCabriolet

B2192 ID DISCORD, IMMU-ECM

SEC-53

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

B2192 ID DISCORD, IMMU-ECM

DTC Logic

INFOID:0000000008460520

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460521

PERFORM INITIALIZATION

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

REPLACE BCM

Replace BCM. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 3.

REPLACE ECM

Replace ECM. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 4.

CHECK INTERMITTENT INCIDENT

SEC-54, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2192

ID DISCORD, BCM-ECM

The ID verification result between BCM and
ECM is NG.

• BCM
• ECM

Revision: 2012 October

2013 Murano CrossCabriolet

SEC-54

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2193 CHAIN OF ECM-IMMU

B2193 CHAIN OF ECM-IMMU

DTC Logic

INFOID:0000000008460522

DTC DETECTION LOGIC

NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-66, "DTC Logic"

• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to

BCS-67, "DTC Logic"

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Go to

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008460523

REPLACE BCM

Replace BCM. Refer to

Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.

Can the system be initialized and can the engine be started with registered Intelligent Key?

YES

>> INSPECTION END

>> GO TO 2.

REPLACE ECM

Replace ECM. Refer to

SEC-55, "Diagnosis Procedure"

>> INSPECTION END

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B2193

CHAIN OF BCM-ECM

Inactive communication between ECM
and BCM

• Harness or connectors

(The CAN communication line is
open or shorted.)

• BCM
• ECM

Revision: 2012 October

2013 Murano CrossCabriolet

B2195 ANTI-SCANNING

SEC-55

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SEC

B2195 ANTI-SCANNING

DTC Logic

INFOID:0000000008460524

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

Turn ignition switch ON.

Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES

>> Refer to

>> INSPECTION END.

Diagnosis Procedure

INFOID:0000000008460525

CHECK SELF DIAGNOSTIC RESULT 1

Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Erase DTC.

Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to

SEC-55, "DTC Logic"

Is DTC 2195 detected?

YES

>> GO TO 2.

>> INSPECTION END

CHECK EQUIPMENT OF THE VEHICLE

Check that unspecified accessory part related to engine start is not installed.

Is unspecified accessory part related to engine start installed?

YES

>> GO TO 3.

>> Replace BCM. Refer to

CHECK SELF DIAGNOSTIC RESULT 2

Obtain the customers approval to remove unspecified accessory part related to engine start, and then
remove it.

Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Erase DTC.

Perform DTC CONFIRMATION PROCEDURE for DTC B2195. Refer to

SEC-55, "DTC Logic"

Is DTC B2195 detected?

YES

>> Replace BCM. Refer to