Nissan Murano Z51 (2013 year). Manual

SRC-62

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B142A IGN VOLTAGE

Is the inspection result normal?

YES

>> GO TO 4.

>> Replace wiring harness.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-61, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2012 September

2013 MURANO

B1430 SEAT BELT PRE-TENSIONER

SRC-63

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

B1430 SEAT BELT PRE-TENSIONER

DTC Logic

INFOID:0000000008843413

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-15, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-63, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008843414

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

Possible cause

B1430

PRE-TEN FRONT LH
(Front seat belt pre-tension-
er squib left hand circuit)

[OPEN]

Seat belt pre-tensioner LH
circuit is open

• Connection malfunction or

open circuit of harness and
connector

• Internal malfunction of seat

belt pre-tensioner LH

• Internal malfunction of air bag

diagnosis sensor unit

[VB-SHORT]

Seat belt pre-tensioner LH
circuit is shorted to power
supply circuit

• Connection malfunction or

short circuit to power supply
of harness and connector

• Internal malfunction of seat

belt pre-tensioner LH

• Internal malfunction of air bag

diagnosis sensor unit

[GND-SHORT]

Seat belt pre-tensioner LH
circuit is shorted to ground

• Connection malfunction or

short circuit to ground of har-
ness and connector

• Internal malfunction of seat

belt pre-tensioner LH

• Internal malfunction of air bag

diagnosis sensor unit

[SHORT]

Seat belt pre-tensioner LH
circuits are shorted to each
other

• Connection malfunction or

short circuit of harness and
connector

• Internal malfunction of seat

belt pre-tensioner LH

• Internal malfunction of air bag

diagnosis sensor unit

Revision: 2012 September

2013 MURANO

SRC-64

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1430 SEAT BELT PRE-TENSIONER

Is the inspection result normal?

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER LH

Replace seat belt pre-tensioner LH. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-63, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-63, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2012 September

2013 MURANO

B1431 SEAT BELT PRE-TENSIONER

SRC-65

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

SRC

B1431 SEAT BELT PRE-TENSIONER

DTC Logic

INFOID:0000000008843415

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

Turn ignition switch ON.

Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Without CONSULT

Turn ignition switch ON.

Check the air bag warning lamp status. Refer to

SRC-15, "On Board Diagnosis Function"

NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.

Is malfunctioning part detected?

YES

>> Refer to

SRC-65, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000008843416

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3

minutes or more. (To discharge backup capacitor.)

• Never use unspecified tester or other measuring device.

CHECK HARNESS CONNECTOR

Check the harness connector.
Is the inspection result normal?

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

Possible cause

B1431

PRE-TEN FRONT RH
(Front seat belt pre-tension-
er squib right hand circuit)

[OPEN]

Seat belt pre-tensioner RH
circuit is open

• Connection malfunction or open

circuit of harness and connector

• Internal malfunction of seat belt

pre-tensioner RH

• Internal malfunction of air bag

diagnosis sensor unit

[VB-SHORT]

Seat belt pre-tensioner RH
circuit is shorted to power
supply circuit

• Connection malfunction or short

circuit to power supply of har-
ness and connector

• Internal malfunction of seat belt

pre-tensioner RH

• Internal malfunction of air bag

diagnosis sensor unit

[GND-SHORT]

Seat belt pre-tensioner RH
circuit is shorted to ground

• Connection malfunction or short

circuit to ground of harness and
connector

• Internal malfunction of seat belt

pre-tensioner RH

• Internal malfunction of air bag

diagnosis sensor unit

[SHORT]

Seat belt pre-tensioner RH
circuits are shorted to
each other

• Connection malfunction or short

circuit of harness and connector

• Internal malfunction of seat belt

pre-tensioner RH

• Internal malfunction of air bag

diagnosis sensor unit

Revision: 2012 September

2013 MURANO

SRC-66

< DTC/CIRCUIT DIAGNOSIS >

[FOR USA AND CANADA]

B1431 SEAT BELT PRE-TENSIONER

YES

>> GO TO 2.

>> Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES

>> GO TO 3.

>> Replace wiring harness.

REPLACE SEAT BELT PRE-TENSIONER RH

Replace seat belt pre-tensioner RH. Refer to

SR-27, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-65, "DTC Logic"

Is DTC detected?

YES

>> GO TO 4.

>> INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to

SR-25, "Removal and Installation"

Perform DTC confirmation procedure. Refer to

SRC-65, "DTC Logic"

Is DTC detected?

YES

>> GO TO 1.

>> INSPECTION END

Revision: 2012 September

2013 MURANO

DIAGNOSIS SENSOR UNIT

SRC-67

< ECU DIAGNOSIS INFORMATION >

[FOR USA AND CANADA]

SRC

ECU DIAGNOSIS INFORMATION

DIAGNOSIS SENSOR UNIT

DTC Index

INFOID:0000000008843424

DTC

Diagnostic item

Number of times of warning lamp

blinking in diagnosis mode

Reference page

System display

Item display

U1000

CAN COMM CIRCUIT

—

SRC-21, "DTC
Logic"

U1010

CONTROL UNIT (CAN)

—

SRC-22, "DTC
Logic"

B0001

DRIVER AIRBAG MODULE

[OPEN]

Front air bag system

SRC-23, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0002

DRIVER AIRBAG MODULE 2

[OPEN]

Front air bag system

SRC-26, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0010

ASSIST A/B MODULE

[OPEN]

Front air bag system

SRC-29, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0011

ASSIST A/B MODULE 2

[OPEN]

Front air bag system

SRC-31, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0020

SIDE A/B MODULE LH

[OPEN]

Side air bag system

SRC-33, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0021

CURTAIN A/B MODULE LH

[OPEN]

Side air bag system

SRC-35, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0028

SIDE A/B MODULE RH

[OPEN]

Side air bag system

SRC-37, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B0029

CURTAIN A/B MODULE RH

[OPEN]

Side air bag system

SRC-39, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

Revision: 2012 September

2013 MURANO

SRC-68

< ECU DIAGNOSIS INFORMATION >

[FOR USA AND CANADA]

DIAGNOSIS SENSOR UNIT

B0091

B-PILLAR SAT SEN LH

[RESET]

Sensor system

SRC-41, "DTC
Logic"

[COMM ERR]

[OPEN]

[UNMATCH]

[OFFSET ERR]

[SELF-DIAG ERR]

[LOWER LIMIT ERR]

[UPPER LIMIT ERR]

[GND-SHORT]

B0094

CRASH ZONE SENS

[RESET]

Sensor system

SRC-43, "DTC
Logic"

[COMM ERR]

[OPEN]

[UNMATCH]

[OFFSET ERR]

[SELF-DIAG ERR]

[LOWER LIMIT ERR]

[UPPER LIMIT ERR]

[GND-SHORT]

B0096

B-PILLAR SAT SEN RH

[RESET]

Sensor system

SRC-45, "DTC
Logic"

[COMM ERR]

[OPEN]

[UNMATCH]

[OFFSET ERR]

[SELF-DIAG ERR]

[LOWER LIMIT ERR]

[UPPER LIMIT ERR]

[GND-SHORT]

B0099

SATELLITE SENSOR

[RESET]

Sensor system

SRC-47, "DTC
Logic"

[COMM ERR]

[OPEN]

[UNMATCH]

[OFFSET ERR]

[SELF-DIAG ERR]

[LOWER LIMIT ERR]

[UPPER LIMIT ERR]

[GND-SHORT]

B00A0

OCCUPANT SENS

[ABNOMAL VOLT-
AGE]

Air bag control unit
system

SRC-49, "DTC
Logic"

[UNIT MALFUNC]

OCCUPANT SENS C/U

[UNIT MALFUNC]

[RESET]

[COMM ERR]

[UNDEFINED]

DTC

Diagnostic item

Number of times of warning lamp

blinking in diagnosis mode

Reference page

System display

Item display

Revision: 2012 September

2013 MURANO

DIAGNOSIS SENSOR UNIT

SRC-69

< ECU DIAGNOSIS INFORMATION >

[FOR USA AND CANADA]

SRC

B00D5

PASS A/B INDCTR CKT

[UNIT MALFUNC]

Air bag control unit
system

SRC-51, "DTC
Logic"

[PWR-SHORT/
OPEN]

[OPEN]

[VB-SHORT]

[GND-SHORT]

B1400-B1405

CONTROL UNIT

[UNIT MALFUNC]

Air bag control unit
system

SRC-53, "DTC
Logic"

B1406-B1410

CONTROL UNIT

[UNIT MALFUNC]

Air bag control unit
system

SRC-54, "DTC
Logic"

B1411-B1415

CONTROL UNIT

[UNIT MALFUNC]

Air bag control unit
system

SRC-55, "DTC
Logic"

B1416-B1420

CONTROL UNIT

[UNIT MALFUNC]

Air bag control unit
system

SRC-56, "DTC
Logic"

B1421

FRONTAL COLLISION

—

Air bag control unit
system

SRC-57, "DTC
Logic"

B1422

SIDE COLLISION

—

Air bag control unit
system

SRC-58, "DTC
Logic"

B1423

ROLLOVER DETECTION

—

Air bag control unit
system

SRC-59, "DTC
Logic"

B1425

REAR COLLISION

—

Air bag control unit
system

SRC-60, "DTC
Logic"

B142A

IGNITION VOLTAGE

[VB-LOW]

—

SRC-61, "DTC
Logic"

[VB-HIGH]

—

B1430

PRE-TEN FRONT LH

[OPEN]

Front air bag system

SRC-63, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

B1431

PRE-TEN FRONT RH

[OPEN]

Front air bag system

SRC-65, "DTC
Logic"

[VB-SHORT]

[GND-SHORT]

[SHORT]

DTC

Diagnostic item

Number of times of warning lamp

blinking in diagnosis mode

Reference page

System display

Item display

Revision: 2012 September

2013 MURANO

SRC-72

< SYMPTOM DIAGNOSIS >

[FOR USA AND CANADA]

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

SYMPTOM DIAGNOSIS

SRS AIR BAG WARNING LAMP DOES NOT TURN OFF

Diagnosis Procedure

INFOID:0000000008454757

CHECK FRONT AIR BAG MODULE

Check the deployment of front air bag module.

Is air bag module deployed?

YES

>> Refer to

SR-11, "Removal and Installation"

SR-17, "Removal and Installation"

>> GO TO 2.

CHECK AIR BAG FUSE

Check the air bag fuse. Refer to

PG-113, "Fuse and Fusible Link Arrangement"

Is 10A fuse [No.2, located in fuse block (J/B)] normal?

YES

>> GO TO 4.

>> GO TO 3.

CHECK AIR BAG FUSE AGAIN

Replace air bag fuse and turn ignition switch ON.

Did the air bag fuse blow again?

YES

>> Repair or replace main harness.

>> INSPECTION END

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

Check the screen of CONSULT.
Is the inspection result normal?

YES

>> GO TO 5.

>> Replace air bag diagnosis sensor unit. Refer to

SR-25, "Removal and Installation"

CHECK HARNESS CONNECTION

Check harness connection between air bag warning lamp and air bag diagnosis sensor unit.

Is the inspection result normal?

YES

>> Check the intermittent incident. Refer to

GI-45, "Intermittent Incident"

>> Replace wiring harness connector.

Revision: 2012 September

2013 MURANO

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

SRC-73

< SYMPTOM DIAGNOSIS >

[FOR USA AND CANADA]

SRC

SRS AIR BAG WARNING LAMP DOES NOT TURN ON

Diagnosis Procedure

INFOID:0000000008454758

CHECK METER FUSE

Check the meter fuse. Refer to

PG-113, "Fuse and Fusible Link Arrangement"

Is 10A fuse [No.4, located in fuse block (J/B)] normal?

YES

>> GO TO 3.

>> GO TO 2.

CHECK METER FUSE AGAIN

Replace 10A fuse [No.4, located in fuse block (J/B)] and turn ignition switch ON.
Did the meter fuse blow again?

YES

>> Repair or replace the related harness.

>> INSPECTION END

CHECK HARNESS CONNECTION

Check harness connection between air bag diagnosis sensor unit and combination meter.

Disconnect air bag diagnosis sensor unit connector and turn ignition switch ON.

Did air bag warning lamp turn ON?

YES

>> Replace air bag diagnosis sensor unit. Refer to

SR-25, "Removal and Installation"

>> Replace combination meter assembly. Refer to

MWI-94, "Removal and Installation"

Revision: 2012 September

2013 MURANO

SRC-74

< SYMPTOM DIAGNOSIS >

[FOR USA AND CANADA]

PASSENGER SEAT BELT WARNING SYSTEM

PASSENGER SEAT BELT WARNING SYSTEM

Diagnosis Procedure

INFOID:0000000008454759

CHECK THE SYSTEM 1

Check the seat belt warning lamp function.

Seat belt warning lamp turns ON in the following conditions.
• Driver seat belt is fastened.
• Occupant is on front passenger seat.
• Front passenger seat belt is not fastened.

Is the inspection result normal?

YES

>> GO TO 2.

Check the followings.

• Harness between air bag diagnosis sensor unit and combination meter.
• Seat belt buckle switch (front passenger side) circuit.
• Seat belt buckle switch (front passenger side).

If these are OK, replace air bag diagnosis sensor unit.

CHECK THE SYSTEM 2

Check the seat belt warning lamp function.

Seat belt warning lamp turns OFF in the following conditions.
• Driver seat belt is fastened.
• Occupant is on front passenger seat.
• Front passenger seat belt is fastened.

Is the inspection result normal?

YES

>> System is OK.

Check the followings.

• Seat belt buckle switch (front passenger side) circuit.
• Seat belt buckle switch (front passenger side).

If these are OK, replace air bag diagnosis sensor unit.

Revision: 2012 September

2013 MURANO

PRECAUTIONS

SRC-75

< PRECAUTION >

[FOR USA AND CANADA]

SRC

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000008454760

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Service

INFOID:0000000008454761

• Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
• Before servicing the SRS, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes.
For approximately 3 minutes after the battery negative terminal is removed, it is still possible for the air bag
and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3
minutes have elapsed.

• Diagnosis sensor unit must always be installed with their arrow marks “

⇐

” pointing towards the front of the

vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before installa-
tion and replace as required.

• The spiral cable must be aligned in the neutral position since its rotations are limited. Do not turn steering

wheel and column after removal of steering gear.

• Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad side

facing upward and seat mounted front side air bag module standing with the stud bolt side facing down.

• Conduct self-diagnosis to check entire SRS for proper functioning after replacing any components.
• After air bag inflates, the front instrument panel assembly should be replaced if damaged.
• Always replace instrument panel pad following front passenger air bag deployment.

Occupant Classification System Precaution

INFOID:0000000008454762

• Replace occupant classification system control unit and passenger front seat cushion as an assembly.

Refer to

SE-73, "Removal and Installation"

Revision: 2012 September

2013 MURANO

DIAGNOSIS AND REPAIR WORK FLOW

SRC-77

< BASIC INSPECTION >

[FOR MEXICO]

SRC

INTERVIEW THE CUSTOMER FOR THE SYMPTOM

Interview the customer for the symptom (the condition and the environment when the incident/malfunction
occurs).

>> GO TO 2.

CHECK SYMPTOM

Check the symptom from the customer information.

>> GO TO 3.

CHECK WARNING LAMP OPERATION

Check air bag warning lamp operation in the user mode. Refer to

SRC-83, "On Board Diagnosis Function"

Are any malfunction detected?

YES

>> GO TO 5.

>> GO TO 4.

CHECK LOW VOLTAGE

Check low voltage. Refer to

PG-3, "How to Handle Battery"

Are any malfunction detected?

YES

>> GO TO 9.

>> Check intermittent incident. Refer to

GI-45, "Intermittent Incident"

CHECK SELF DIAGNOSTIC RESULTS

Check self diagnostic result with CONSULT or diagnosis mode.
If it is impossible to switch to diagnosis mode, follow the same procedure that DTC is not detected.
NOTE:
Perform the following procedure if DTC is detected.
• Record DTC (Print them out with CONSULT.)
• Erase self diagnostic result.
• Study the relationship between the malfunction that DTC or air bag warning lamp indicates and the symptom

that the customer describes.

• Check related service bulletins for information.
Is DTC detected?

YES

>> GO TO 6.

>> GO TO 7.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC CONFIRMATION PROCEDURE for the DTC.

>> GO TO 8.

PERFORM DIAGNOSIS ACCORDING TO WARNING LAMP OPERATION

Check air bag warning lamp operation in the user mode. Refer to

SRC-83, "On Board Diagnosis Func-

tion"