Nissan Murano. Manual - part 987

 

  Главная      Nissan     Nissan Murano (2014 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  985  986  987  988   ..

 

 

Nissan Murano. Manual - part 987

 

 

LAN

ADP BRANCH LINE CIRCUIT

LAN-259

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 12)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

ADP BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010093757

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).

-

Driver seat control unit

-

Harness connector B460

-

Harness connector B19

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of driver seat control unit.

2.

Check the resistance between the driver seat control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the driver seat control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the driver seat control unit. Refer to 

ADP-55, "DRIVER SEAT

CONTROL UNIT : Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the driver seat control unit. Refer to 

ADP-210, "Removal and Installation"

.

YES (Past error)>>Error was detected in the driver seat control unit branch line.
NO

>> Repair the power supply and the ground circuit.

Driver seat control unit harness connector

Resistance (

)

Connector No.

Terminal No.

B452

23

24

Approx. 54 – 66

LAN-260

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 12)]

AVM BRANCH LINE CIRCUIT

AVM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010093758

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the camera control unit for damage, bend and loose connection
(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of camera control unit.

2.

Check the resistance between the camera control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the camera control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the camera control unit. Refer to 

DAS-165, "CAMERA CON-

TROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the camera control unit. Refer to 

DAS-187, "Removal and Installation"

.

YES (Past error)>>Error was detected in the camera control unit branch line.
NO

>> Repair the power supply and the ground circuit.

Camera control unit harness connector

Resistance (

)

Connector No.

Terminal No.

B92

27

28

Approx. 54 – 66

LAN

PWBD BRANCH LINE CIRCUIT

LAN-261

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 12)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

PWBD BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010093759

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the automatic back door control unit for damage, bend and loose
connection (unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of automatic back door control unit.

2.

Check the resistance between the automatic back door control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the automatic back door control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the automatic back door control unit. Refer to 

DLK-95,

"AUTOMATIC BACK DOOR CONTROL UNIT : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the automatic back door control unit. Refer to 

DLK-368, "Removal and Instal-

lation"

.

YES (Past error)>>Error was detected in the automatic back door control unit branch line.
NO

>> Repair the power supply and the ground circuit.

Automatic back door control unit harness connector

Resistance (

)

Connector No.

Terminal No.

B8

6

7

Approx. 54 – 66

LAN-262

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 12)]

4WD BRANCH LINE CIRCUIT

4WD BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000010093760

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the AWD control unit for damage, bend and loose connection (unit
side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of AWD control unit.

2.

Check the resistance between the AWD control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the AWD control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the AWD control unit. Refer to 

DLN-21, "Diagnosis Proce-

dure"

.

Is the inspection result normal?

YES (Present error)>>Replace the AWD control unit. Refer to 

DLN-53, "Removal and Installation"

.

YES (Past error)>>Error was detected in the AWD control unit branch line.
NO

>> Repair the power supply and the ground circuit.

AWD control unit harness connector

Resistance (

)

Connector No.

Terminal No.

M69

8

16

Approx. 54 – 66

 

 

 

 

 

 

 

содержание   ..  985  986  987  988   ..