Nissan Murano. Manual - part 181

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-33

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored. 

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY ON” on CONSULT screen is touched.
• “KEY” Warning lamp flashes when “KEY IND” on CONSULT screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

BCS-34

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

COMB SW

COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000009722450

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

LCD

This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT screen is touched.
• Engine start information displays when “BP I” on CONSULT screen is touched.
• Key ID warning displays when “ID NG” on CONSULT screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT screen is touched.

NOTE:
For models without steering lock unit, “ROTAT” is displayed, but cannot be tested.

• P position warning displays when “SFT P” on CONSULT screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT screen is touched.
• Take away warning display when “OUTKEY” on CONSULT screen is touched.
• OFF position warning display when “LK WN” on CONSULT screen is touched.

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
The hazard warning lamps will be activated after “ON” on CONSULT screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT screen is touched.

IGN CONT2

This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT screen is touched.

P RANGE

This test is able to check CVT shift selector power supply
CVT shift selector power is supplied when “ON” on CONSULT screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched.

LOCK INDICATOR

NOTE:
This item is displayed, but cannot be tested.

ACC INDICATOR

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.

IGNITION ON IND

This test is able to check indicator in push-ignition switch operation.
Indicator in push-button ignition switch illuminates when “ON” on CONSULT screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT screen is touched.

AUTOMATIC BACK DOOR

NOTE:
This item is displayed, but cannot be tested.

AUTOMATIC SLIDING DOOR

NOTE:
This item is displayed, but cannot be tested.

Test item

Description

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination 
switch reading function.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-35

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM

BCM : CONSULT Function (BCM - BCM)

INFOID:0000000009722451

WORK SUPPORT

IMMU

IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000010074033

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

DATA MONITOR

NOTE:

FR WIPER STOP
[Off/On]

Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.

INT VOLUME
[1 - 7]

Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading 
function.

RR WIPER ON
[Off/On]

Displays the status of the RR WIPER ON switch in combination switch judged by BCM with the combination 
switch reading function.

RR WIPER INT
[Off/On]

Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination 
switch reading function.

RR WASHER SW
[Off/On]

Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination 
switch reading function.

RR WIPER STOP
[Off/On]

Displays the status of the rear wiper stop position signal received from rear wiper motor.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch 
reading function.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch 
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination 
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch 
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination 
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination 
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch 
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination 
switch reading function.

FR FOG SW
[Off/On]

Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch 
reading function.

RR FOG SW
[Off/On]

NOTE:
The item is indicated, but not monitored.

Monitor item [UNIT]

Description

Item

Description

RESET SETTING VALUE

Return a value set with Work Support of each system to a default value in factory shipment.

Diagnosis mode

Function Description

DATA MONITOR

The BCM input/output signals are displayed.

ACTIVE TEST

The signals used to activate each device are forcibly supplied from BCM.

BCS-36

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM)

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

BATTERY SAVER

BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000010074040

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Monitor item 

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

TP 4

Indicates the number of ID which has been registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT screen touched.

Service item

Setting item

Setting

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ROOM LAMP BAT SAV SET

On*

With the interior room lamp battery saver function

Off

Without the interior room lamp battery saver function

ROOM LAMP TIMER SET

MODE 1

30 min.

Sets the interior room lamp battery saver timer operating 
time. 

MODE 2

60 min.

MODE 3*

15 min.

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

The switch status input from request switch (driver side)

REQ SW-AS
[On/Off]

The switch status input from front request switch (passenger side)

REQ SW-RR
[On/Off]

NOTE:
The item is indicated, but not monitored.

REQ SW-RL
[On/Off]