Nissan Murano. Manual - part 1053

 

  Главная      Nissan     Nissan Murano (2014 year) - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  1051  1052  1053  1054   ..

 

 

Nissan Murano. Manual - part 1053

 

 

MWI-92

< ECU DIAGNOSIS INFORMATION >

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)

NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.

STARTER MOTOR PROTECTION FUNCTION

IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.

DTC Index

INFOID:0000000010088711

NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame data).
- The number is 0 when is detected now.
- The number increases like 1 

 2 ··· 38 

 39 after returning to the normal condition whenever IGN OFF 

ON.

- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

×

: Applicable

CONSULT display

Fail-safe

Refer to

No DTC is detected.
further testing
may be required.

U1000: CAN COMM CIRCUIT

×

PCS-15

B2098: IGN RELAY ON CIRC

×

PCS-16

B2099: IGN RELAY OFF CIRC

PCS-18

B210B: STR CONT RLY ON CIRC

SEC-79

B210C: STR CONT RLY OFF CIRC

SEC-80

B210D: STARTER RLY ON CIRC

SEC-81

B210E: STARTER RLY OFF CIRC

SEC-83

B210F: INTRLCK/PNP SW ON

SEC-85

B2110: INTRLCK/PNP SW OFF

SEC-87

MWI

THE FUEL GAUGE POINTER DOES NOT MOVE

MWI-93

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYMPTOM DIAGNOSIS

THE FUEL GAUGE POINTER DOES NOT MOVE

Description

INFOID:0000000009721310

Fuel gauge needle will not move from a certain position.

Diagnosis Procedure

INFOID:0000000009721311

1.

CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE

Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
Refer to 

MWI-34, "Diagnosis Description"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the combination meter. 

2.

CHECK FLOAT INTERFERENCE

Check that the float arm interferes with or binds to other components in the fuel tank.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning part.

3.

CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT

Check the fuel level sensor signal circuit. Refer to 

MWI-46, "Component Function Check"

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

MWI-94

< SYMPTOM DIAGNOSIS >

THE METER CONTROL SWITCH IS INOPERATIVE

THE METER CONTROL SWITCH IS INOPERATIVE

Description

INFOID:0000000009721312

If any of the following malfunctions is found for the meter control switch operation.
• All switches are inoperative.
• The specified switch cannot be operated.

Diagnosis Procedure

INFOID:0000000009721313

1.

CHECK METER CONTROL SWITCH SIGNAL CIRCUIT

Check the meter control switch signal circuit. Refer to 

MWI-49, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair harness or connector.

2.

CHECK METER CONTROL SWITCH

Perform a unit check for the meter control switch. Refer to 

MWI-50, "Component Inspection"

Is the inspection result normal?

YES

>> Replace combination meter.

NG

>> Replace meter control switch.

MWI

THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON

MWI-95

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

THE OIL PRESSURE WARNING LAMP DOES NOT TURN ON

Description

INFOID:0000000009721314

The oil pressure warning lamp stays off when the ignition switch is turned ON.

Diagnosis Procedure

INFOID:0000000009721315

1.

CHECK OIL PRESSURE WARNING LAMP

Perform auto active test. Refer to 

PCS-10, "Diagnosis Description"

.

Is oil pressure warning lamp blinking?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OIL PRESSURE SWITCH SIGNAL CIRCUIT

Check the oil pressure switch signal circuit. Refer to 

MWI-52, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair harness or connector.

3.

CHECK OIL PRESSURE SWITCH

Perform a unit check for the oil pressure switch. Refer to 

MWI-52, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R. 

NO

>> Replace oil pressure switch.

4.

CHECK COMBINATION METER INPUT SIGNAL

Connect CONSULT and perform an input signal check for the combination meter. Refer to 

MWI-52, "Compo-

nent Function Check"

.

Is the inspection result normal?

YES

>> Replace combination meter.

NO

>> Replace IPDM E/R. Refer to 

PCS-37, "Removal and Installation"

.

 

 

 

 

 

 

 

содержание   ..  1051  1052  1053  1054   ..