Nissan X-Trail 32. Manual - part 797

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  795  796  797  798   ..

 

 

Nissan X-Trail 32. Manual - part 797

 

 

P0607 ECM

EC-317

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P0607 ECM

DTC Description

INFOID:0000000010775211

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

POSSIBLE CAUSE

ECM

FAIL-SAFE

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Check 1st trip DTC.

Is 1st trip DTC detected?

YES

>> Proceed to 

EC-317, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010775212

1.

INSPECTION START

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Perform “DTC Confirmation Procedure”. Refer to 

EC-317, "DTC Description"

.

Is 1st trip DTC detected?

YES

>> Replace ECM. Refer to 

EC-430, "Removal and Installation"

.

NO

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

P0607

ECM
(Control module performance)

When detecting error during the initial diagnosis of CAN controller of ECM.

Engine operating condition in fail-safe mode

Fail safe mode

Vehicle behavior

Traveling con-
trol mode

Accelerator an-
gle variation 
control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This 
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.

Engine output 
control

ECM reduces the engine output, according to the rise in engine speed. This reduces the vehicle 
speed to encourage the driver to repair malfunction.

EC-318

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

P0611 ECM PROTECTION

P0611 ECM PROTECTION

DTC Description

INFOID:0000000010775213

This DTC is detected when the ECM protective function is activated due to an extreme temperature increasein
ECM, resulting from severe conditions such as heavy load driving.

DTC DETECTION LOGIC

POSSIBLE CAUSE

ECM overheating 

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

This DTC is displayed as protection function history. If no malfunction is detected after the diagnosis, the cus-
tomer must be informed of the activation of the protection function.

>> Proceed to 

EC-318, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010775214

1.

INSPECTION START

1.

“DTC Confirmation Procedure”. Refer to 

EC-318, "DTC Description"

.

2.

Check 1st trip DTC.

Is the 1st trip DTC P0611 detected?

YES

>> Proceed to 

EC-318, "DTC Description"

.

NO

>> Explain the customer about the activation of the protection function.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

P0611

FIC MODULE

ECM overheat protection control is activated.

P062B ECM

EC-319

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P062B ECM

DTC Description

INFOID:0000000010775215

This DTC is detected when the ECM-integrated injector driver unit has a malfunction.

DTC Logic

INFOID:0000000010775216

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connectors (Fuel injector circuit is open or shorted.)
• Battery power supply
• ECM (Injector driver unit)

FAIL-SAFE

NOTE:
Fail-safe mode may not start depending on malfunction type of ECM.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

1.

Turn ignition switch OFF and wait at least 10 seconds.

2.

Turn ignition switch ON.

3.

Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Start the engine and keep the engine speed at idle for 30 seconds.

2.

Check 1st trip DTC.

Is 1st trip DTC detected?

YES

>> Proceed to 

EC-319, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010775217

1.

CHECK FUEL INJECTOR

Check fuel injector. Refer to 

EC-386, "Component Function Check"

.

Is inspection result normal?

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

P062B

ECM
(Internal control module fuel injector control 
performance)

Injector driver unit is malfunctioning.

Engine operating condition in fail-safe mode

Fail safe mode

Vehicle behavior

Traveling con-
trol mode

Accelerator an-
gle variation 
control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This 
causes a drop in accelerating performance and encourages the driver to repair malfunction.
NOTE:
ECM does not control the accelerator pedal releasing speed.

Combustion 
control mode

Stratified charge 
combustion 
control at start-
ing

No stratified charge combustion at starting (cold start).

EC-320

< DTC/CIRCUIT DIAGNOSIS >

[MR20DD]

P062B ECM

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Erase DTC.

3.

Perform DTC confirmation procedure again. Refer to 

EC-319, "DTC Logic"

.

4.

Check 1st trip DTC.

Is the DTC P062B displayed again?

YES

>> Replace ECM. Refer to 

EC-430, "Removal and Installation"

.

NO

>> INSPECTION END

 

 

 

 

 

 

 

содержание   ..  795  796  797  798   ..