Nissan X-Trail 32. Manual - part 532

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  530  531  532  533   ..

 

 

Nissan X-Trail 32. Manual - part 532

 

 

AUTOMATIC BACK DOOR CLOSE SWITCH

DLK-469

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH

Refer to 

DLK-469, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace automatic back door close switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010717515

1.

CHECK AUTOMATIC BACK DOOR CLOSE SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect automatic back door close switch connector.

3.

Check continuity between automatic back door close switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace automatic back door close switch.

Automatic back door close switch

Ground

Continuity 

 Connector

Terminal

D173

2

Existed

Automatic back door close switch

Condition

Continuity 

Terminal

1

2

Automatic back door 
close switch 

Pressed

Existed

Released

Not existed

DLK-470

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

AUTOMATIC BACK DOOR SWITCH

AUTOMATIC BACK DOOR SWITCH

Component Function Check

INFOID:0000000010717516

1.

CHECK FUNCTION

1.

Turn ignition switch ON.

2.

Select “AUTO BACK DOOR” using CONSULT.

3.

Select “AUTO BD SW” in “DATA MONITOR” mode.

4.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Automatic back door switch is OK.

NO

>> Refer to 

DLK-470, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010717517

1.

CHECK AUTOMATIC BACK DOOR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect automatic back door switch connector.

3.

Check voltage between automatic back door switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK AUTOMATIC BACK DOOR SWITCH CIRCUIT

1.

Disconnect automatic back door control unit connector.

2.

Check continuity between automatic back door control unit harness connector and automatic back door
switch harness connector.

3.

Check continuity between automatic back door control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK AUTOMATIC BACK DOOR SWITCH GROUND CIRCUIT

Check continuity between automatic back door switch harness connector and ground.

Monitor item

Condition

Status

 AUTO BD SW 

Automatic back door switch

Pressed

ON

Released

OFF

(+)

(–)

Voltage

(Approx.)

Automatic back door switch

Connector

Terminal

M58

1

Ground

12.6 V

Automatic back door control unit

Automatic back door switch

Continuity 

 Connector

Terminal

Connector

Terminal

B24

22

M58

1

Existed

Automatic back door control unit

Ground

Continuity 

 Connector

Terminal

B24

22

Not existed

AUTOMATIC BACK DOOR SWITCH

DLK-471

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK AUTOMATIC BACK DOOR SWITCH

Refer to 

DLK-471, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace automatic back door switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010717518

1.

CHECK AUTOMATIC BACK DOOR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect automatic back door switch connector.

3.

Check continuity between automatic back door switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace automatic back door switch.

Automatic back door switch

Ground

Continuity 

Connector

Terminal

M58

2

Existed

Automatic back door switch

Condition

Continuity 

Terminal

1

2

Automatic back door switch

Pressed

Existed

Released

Not existed

DLK-472

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

AUTOMATIC DOOR MAIN SWITCH

AUTOMATIC DOOR MAIN SWITCH

Component Function Check

INFOID:0000000010717519

1.

CHECK FUNCTION

1.

Turn ignition switch ON.

2.

Select “AUTO BACK DOOR” using CONSULT.

3.

Select “MAIN SW” in “DATA MONITOR” mode.

4.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Automatic door main switch is OK.

NO

>> Refer to 

DLK-472, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010717520

1.

CHECK AUTOMATIC BACK DOOR MAIN SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect automatic back door main switch connector.

3.

Check voltage between automatic back door main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK AUTOMATIC BACK DOOR MAIN SWITCH CIRCUIT

1.

Disconnect automatic back door control unit connector.

2.

Check continuity between automatic back door control unit harness connector and automatic back door
main switch harness connector.

3.

Check continuity between automatic back door control unit connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK AUTOMATIC BACK DOOR MAIN SWITCH GROUND CIRCUIT

Check continuity between automatic back door main switch connector and ground.

Monitor item

Condition

Status

 MAIN SW

Automatic door main switch

ON

ON

OFF

OFF

(+)

(–)

Voltage

(Approx.)

Automatic back door main switch

Connector

Terminal

M54

1

Ground

12.2 V

Automatic back door control unit

Automatic back door main switch

Continuity 

Connector

Terminal

Connector

Terminal

B24

10

M54

1

Existed

Automatic back door control unit

Ground

Continuity 

Connector

Terminal

B24

10

Not existed

 

 

 

 

 

 

 

содержание   ..  530  531  532  533   ..