Nissan X-Trail 32. Manual - part 528

B2427 ENCODER

DLK-453

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

4.

CHECK ENCODER POWER SUPPLY

1.

Turn ignition switch OFF.

2.

Disconnect spindle unit RH connector.

3.

Check voltage between spindle unit RH harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> GO TO 5.

5.

CHECK ENCODER CIRCUIT

1.

Disconnect automatic back door control unit connector.

2.

Check continuity between automatic back door control unit harness connector and spindle unit RH har-
ness connector.

3.

Check continuity between automatic back door control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

NO

>> Repair or replace harness.

6.

CHECK ENCODER CIRCUIT 2

1.

Disconnect automatic back door control unit connector.

2.

Check continuity between automatic back door control unit harness connector and spindle unit RH har-
ness connector.

3.

Check continuity between automatic back door control unit harness connector and ground.

Monitor item

Condition

Status

SPINDLE RH ENCODER A

Back door

Moving (auto or manu-
al)

HI 

⇔

 LO

When stopped

HI or LO

SPINDLE RH ENCODER B

Moving (auto or manu-
al)

HI 

⇔

 LO

When stopped

HI or LO

(+)

(–)

Voltage

(Approx.)

Spindle unit RH

Connector

Terminal

B29

3

Ground

12.3 V

Automatic back door control unit

Spindle unit RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B24

20

B29

3

Existed

Automatic back door control unit

Ground

Continuity 

 Connector

Terminal

B24

20

Not existed

Automatic back door control unit

Spindle unit RH

Continuity 

 Connector

Terminal

 Connector

Terminal

B24

21

B29

6

Existed

DLK-454

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

B2427 ENCODER

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace harness.

7.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace the malfunctioning parts.

8.

REPLACE SPINDLE UNIT

1.

Replace spindle unit

2.

Erase DTC.

3.

Perform DTC confirmation procedure for DTC 2427. Refer to 

DLK-452, "DTC Description"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

Automatic back door control unit

Ground

Continuity 

 Connector

Terminal

B24

21

Not existed

B2428 AUTOMATIC BACK DOOR CONTROL UNIT

DLK-455

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

B2428 AUTOMATIC BACK DOOR CONTROL UNIT

DTC Description

INFOID:0000000010717499

DTC DETECTION LOGIC

POSSIBLE CAUSE

Automatic back door control unit

FAIL-SAFE

Inhibit automatic back door operation

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Operate automatic back door.

3.

Check “Self Diagnostic Result” mode of “AUTO BACK DOOR” using CONSULT.

Is DTC detected?

YES

>> Refer to 

DLK-455, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010717500

1.

REPLACE AUTOMATIC BACK DOOR CONTROL UNIT

When DTC B2428 is detected, replace automatic back door control unit.

>> Replace automatic back door control unit. Refer to 

DLK-633, "Removal and Installation"

.

DTC No.

CONSULT screen items (Trou-

ble diagnosis content)

DTC detecting condition

B2428

AUTO BACK DR CNT UNIT

(Auto back door control unit)

Automatic back door control unit detected CPU malfunction

DLK-456

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 2]

B242A CLOSURE CONDITION

B242A CLOSURE CONDITION

DTC Description

INFOID:0000000010717501

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Entry of foreign materials to back door lock assembly
• Back door mechanism
• Close switch
• Half latch switch
• Open switch
• Harness or connectors (open or shorted)
• Automatic back door control unit

FAIL-SAFE

Inhibit automatic back door operation

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Operate back door auto closure operation.

3.

Check “Self Diagnostic Result” mode of “AUTO BACK DOOR” using CONSULT.

Is DTC detected?

YES

>> Refer to 

DLK-456, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010717502

1.

CHECK FOR FOREIGN MATERIALS IN BACK DOOR LOCK ASSEMBLY

Check for entry of foreign materials in back door lock assembly.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Remove foreign materials.

2.

CHECK BACK DOOR OPEN/CLOSE OPERATION

Manually check open and close operation of back door.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK MONITOR ITEM

1.

Turn ignition switch ON.

2.

Select “AUTO BACK DOOR” using CONSULT.

3.

Select “HALF LATCH SW”, “OPEN SW” and “CLOSE SW” in “DATA MONITOR” mode.

4.

Check that the function operates normally according to the following conditions.

DTC No.

CONSULT screen items (Trou-

ble diagnosis content)

DTC detecting condition

B242A

CLSR CONDITION

(Closure condition)

Automatic back door control unit detects malfunctions of open switch, 
close switch and half latch switch when auto closure of back door operates