Nissan X-Trail 32. Manual - part 434

DIAGNOSIS SYSTEM (BCM)

DLK-77

< SYSTEM DESCRIPTION >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

ACC BATTERY SAVER

Indicates [On/Off] whether or not ignition battery saver is in operation

CRNK PRBT TMR

Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection 
function operation

AUT CRANK TMR

Indicates [On/Off] whether or not in AUTO CRANKING MODE status

CRNK PRBT TME

Indicates the time for changing from cranking prohibited status to cranking possible status

AUT CRANK TMR

Indicates the time that AUTO CRANKING MODE operates

CRANKING TME

Indicates the cranking operation time

SHORT CRANK

NOTE:
This item is displayed, but not used

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intel-
ligent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored 

S/L IGN OFF POSITION

Indicates [On/Off] condition of Ignition OFF signal

S/L SENSOR CIRCUIT 1

Indicates [Gnd/On] condition of steering lock unit sensor circuit

S/L SENSOR CIRCUIT 2

Indicates [On/Off] condition of steering lock unit sensor circuit

S/L POWER OUTPUT

Indicates [On/Off] condition of steering lock unit power supply

S/L POWER CHECK

Indicates [On/Off] condition of steering lock unit power supply

ANTICIPATED POWER

Indicates [On/Off] condition of anticipated power supply

S/L LOCK REQ

Indicates [On/Off] condition of steering lock unit lock request signal

S/L - BCM (CAN)

Indicates [On/Off] condition of CAN communication

S/L POWER ERROR

Indicates [On/Off] condition of steering lock unit power supply error

VEH SPEED ERROR (S/L)

Indicates [On/Off] condition of vehicle speed signal

VEH SPEED NORMAL (S/L)

Indicates [On/Off] condition of vehicle speed signal

ENGINE RUNNING (S/L)

Indicates [On/Off] condition of engine running

S/L ID DISCORD

Indicates [Correct/Incorrect] condition of ID verification

S/L ANTI-SCAN MODE

Indicates [On/Off] condition of antiscan mode

S/L LOCK NOT PERMIT

Indicates [Inhibition/No inhbt] condition of inhibit steering lock

S/L UNLOCK (CAN)

Indicates [Finished/Unfinished] condition of steering lock unit unlock

S/L ID STATUS (CAN)

Indicates [Coded/Blank] condition of registration ID

S/L RESET STATUS (CAN)

Indicates [Exit/No exit] condition of steering lock unit reset signal

S/L LO-LEVEL MALFUNC 
(CAN)

Indicates [Malf/No malf] condition of lo-level malfunction

S/L LOCK POSITION (CAN)

Indicates [Armed/Malf/Unlocked/Undefined] condition of lock/unlock position signal

S/L ACT MALFUNCTION (CAN)

Indicates [Malf/No malf] condition of steering lock unit malfunction

S/L HI-LEVEL MALFUNC (CAN)

Indicates [Malf/No malf] condition of hi-level malfunction

S/L OPERATION PRHBT (SPD)

Indicates [On/Off] condition of vehicle speed signal

S/L OPERATION PRHBT (PWR)

Indicates [Allowed/Forbid] condition of safety line inhibition

S/L SENSOR POWER (CAN)

Indicates [On/Off] condition of sensor test power supply

S/L SEN TEST PERMIT (CAN)

Indicates [Forbid/Authorize] condition of sensor test

S/L STAT NOT DETECT (CAN)

Indicates [Ok/Undefind] condition of steering lock undefined position signal

S/L LOCKING FINISHED (CAN)

Indicates [Unfinshd/Finished] condition of steering lock unit lock status signal

STOP/START SW

Indicates [On/Off] condition of stop/start off switch

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

Monitor Item

Condition

DLK-78

< SYSTEM DESCRIPTION >

[TYPE 1]

DIAGNOSIS SYSTEM (BCM)

*

1

: It is displayed but does not operate on CVT models.

*

2

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored 

RKE-PANIC

NOTE:
This item is displayed, but cannot be monitored 

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE PBD

Indicates [On/Off] condition of back door open request signal from Intelligent Key

KEY SW

NOTE:
This item is displayed, but cannot be monitored 

IGN SW

NOTE:
This item is displayed, but cannot be monitored 

START SW

NOTE:
This item is displayed, but cannot be monitored 

Monitor Item

Condition

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Buzzer 1: Combination meter buzzer sounds (pipipi...) when CONSULT screen is touched
• Buzzer 2: Combination meter buzzer sounds (pipi-pipi-...) when CONSULT screen is 

touched

• Buzzer 3: Combination meter buzzer sounds (pipipipi-pipipipi-...) when CONSULT screen is 

touched

• Off: Non-operation

INDICATOR

This test is able to check warning lamp operation
• KEY ON: [Intelligent Key system malfunction] displays when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched

HORN

NOTE:
This item is displayed, but cannot be used

IGN CONT2

This test is able to operate the blower relay in fuse block (J/B)
• On: Operates
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched

ENGINE START REQUEST

This test is able to check BCM sends starter request signal to IPDM E/R via CAN communi-
cation
• MODE 1: IGN ON, START request OFF
• MODE 2: IGN OFF, START request ON
• MODE 3: IGN ON, START request ON
• Off: Non-operation

IGNITION RELAY

NOTE:
This item is displayed, but cannot be used

STARTER CUT RELAY

This test is able to operate the starter control relay
• On: Operates
• Off: Non-operation

ENGINE START

NOTE:
This item is displayed, but cannot be used

DIAGNOSIS SYSTEM (BCM)

DLK-79

< SYSTEM DESCRIPTION >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

TRUNK

TRUNK : CONSULT Function (BCM - TRUNK) (With Intelligent Key System and Super 
Lock)

INFOID:0000000010708059

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

TRUNK/BACK DOOR

NOTE:
This item is displayed, but cannot be used

RETRACTABLE MIRROR

NOTE:
This item is displayed, but cannot be used

AUTO ACC 2

This test is able to check BCM sends power supply to audio unit or NAVI control unit
• On: Operate
• Off: Non-operation

AUTOMATIC BACK DOOR

NOTE:
This item is displayed, but cannot be used

AUTO ACC 1

This test is able to check BCM sends power supply to ignition relay
• On: Operate
• Off: Non-operation

TRUNK/LUGGAGE LAMP 
TEST

This test is able to check trunk/luggage room lamp operation
• On: Operates
• Off: Non-operation

Test item

Description

Monitor Item

Contents

PUSH SW

Indicates [On/Off] condition of push switch

STARTER CUT RELAY

Indicates [On/Off] condition of starter control relay

DETECTION SENSOR (BK)

NOTE:
This item is displayed, but cannot be monitored

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter

KEY CYL SW-TR

NOTE:
This item is displayed, but cannot be monitored

TR CANCEL SW

NOTE:
This item is displayed, but cannot be monitored

TRUNK LID OPENER SW

NOTE:
This item is displayed, but cannot be monitored

BACK DOOR OPENER SW

Indicates [On/Off] condition of back door opener switch

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

DLK-80

< SYSTEM DESCRIPTION >

[TYPE 1]

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)

CONSULT Function (AUTOMATIC BACK DOOR CONTROL UNIT)

INFOID:0000000010708060

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with automatic back door control unit.

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Diagnosis mode

Function Description

Work Support

Changes the setting for system function

Self Diagnostic Result

Displays the diagnosis results judged by automatic back door control unit

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from automatic back door 
control unit

Data Monitor

The automatic back door control unit input/output signals are displayed

Ecu Identification

The automatic back door control unit part number is displayed

Monitor Item

Description

SPINDLE SENSOR LH

Indicates [Pulse] condition of encoder LH 

SPINDLE LH SPEED

Indicates [mm/s] condition of spindle motor LH operation speed

SPINDLE MOTOR LH DUTY

Indicates [%] condition of spindle motor LH duty

VHCL SPEED MTR

Display the vehicle speed signal received from unified meter and A/C amp. by numerical 
value [km/h]

VHCL SPEED ABS

Display the vehicle speed signal received from ABS actuator and electrical unit by numer-
ical value [km/h]

MAIN SW

Indicates [ON/OFF] condition of automatic back door main switch

AUTO BD SW

Indicates [ON/OFF] condition of automatic back door switch

BK DOOR CL SW

Indicates [ON/OFF] condition of automatic back door close switch

PKB SW

Indicates [ON/OFF] condition of parking brake status from combination meter via CAN 
communication

BACK DOOR LOCK STATUS

Indicates [ON/OFF] condition of back door lock status

OPEN SW

Indicates [ON/OFF] condition of open switch

CLOSE SW

Indicates [ON/OFF] condition of close switch

HALF LATCH SW

Indicates [ON/OFF] condition of half latch switch

TOUCH SEN RH

Indicates [ON/OFF/OPEN] condition of touch sensor RH

TOUCH SEN LH

Indicates [ON/OFF/OPEN] condition of touch sensor LH

P RANGE IND

Indicates [ON/OFF] condition of P range signal from unified meter and A/C amp.

RKE REQ

Indicates [OFF/MOVE/REV] condition of remote keyless entry signal from BCM

IGN SW

Indicates [ON/OFF] condition of IGN power supply

SPINDLE LH ENCODER A

Indicates [LO/HI] condition of encoder signal A from encoder LH

SPINDLE LH ENCODER B

Indicates [LO/HI] condition of encoder signal B from encoder LH

UNLOCK SEN BD

NOTE:
This item is displayed, but cannot be monitored

DESTINATION

Indicates [Type 1/Type 2/Type 3/Type 4] specification of destination of the automatic back 
door system
Normal: [Type 3] is monitored

TRANSMISSION TYPE

Indicates [MT/(AT/CVT)] type of transmission