Nissan X-Trail 32. Manual - part 372

DAS

C1BAB-00 STOP LAMP SWITCH

DAS-229

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

YES (other DTC)>>Check the DTC.
NO

>> INSPECTION END

DAS-230

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB2-00 CONTROL MODULE

C1BB2-00 CONTROL MODULE

DTC Description

INFOID:0000000010721724

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active trace control function
• Active engine brake function
• Active ride control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB2-00” detected?

YES

>> Proceed to 

DAS-230, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010721725

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB2-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB2-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS

C1BB3-00 CONTROL MODULE

DAS-231

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BB3-00 CONTROL MODULE

DTC Description

INFOID:0000000010721726

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active trace control function
• Active engine brake function
• Active ride control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB3-00” detected?

YES

>> Proceed to 

DAS-231, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010721727

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB3-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB3-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS-232

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BB4-00 CONTROL MODULE

C1BB4-00 CONTROL MODULE

DTC Description

INFOID:0000000010721728

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended.
• Active trace control function
• Active engine brake function
• Active ride control function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB4-00” detected?

YES

>> Proceed to 

DAS-232, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010721729

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1.

Erase self-diagnosis result for “CHASSIS CONTROL”.

2.

Turn the ignition switch OFF and wait for 10 seconds or more.

3.

Turn the ignition switch ON.

4.

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC “C1BB4-00” detected?

YES

>> Replace the chassis control module. Refer to 

DAS-278, "Removal and Installation"

.

NO

>> INSPECTION END

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BB4-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.