Nissan X-Trail 32. Manual - part 2220

LOW TIRE PRESSURE LOCATION INDICATOR DOES NOT DISPLAY

WT-53

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

LOW TIRE PRESSURE LOCATION INDICATOR DOES NOT DISPLAY

Description

INFOID:0000000010715109

When low tire pressure, low tire location indicator does not display though low tire pressure warning lamp
turns ON.

Diagnosis Procedure

INFOID:0000000010715110

1.

CHECK COMBINATION METER

Check combination meter. Refer to 

MWI-118, "Work flow"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

CHECK LOW TIRE PRESSURE WHEEL LOCATION INDICATOR OPERATION

Check that the low tire pressure location indicator is turned OFF after turns ON for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-44, "Intermittent Incident"

.

NO

>> Replace the BCM. Refer to 

BCS-121, "Removal and Installation"

.

WT-54

< SYMPTOM DIAGNOSIS >

LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING

LOW TIRE PRESSURE LOCATION INDICATOR CONTINUES DISPLAYING

Description

INFOID:0000000010715111

The low tire pressure location indicator continues displaying though low tire pressure warning lamp turns/stays
OFF.

Diagnosis Procedure

INFOID:0000000010715112

1.

CHECK TIRE PRESSURE

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Check the tire pressure for all wheels and adjust to the specified value. Refer to 

WT-66, "Tire Air Pres-

sure"

. 

3.

Perform TPMS reset operation. Refer to 

WT-14, "TPMS reset operation"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Inspect or repair the tires or wheels.

2.

CHECK LOW TIRE PRESSURE LOCATION INDICATOR

Check low tire pressure location indicator.

Does low tire pressure location indicator continues displaying?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “AIR PRESSURE MONITOR”.
Is DTC detected?

YES

>> Perform DTC diagnosis procedure. Refer to 

WT-21, "DTC Index"

.

NO

>> GO TO 4.

4.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for power supply and ground circuit. Refer to 

BCS-114, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-121, "Removal and Installation"

. 

NO

>> Repair or replace error-detected parts.

TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED

WT-55

< SYMPTOM DIAGNOSIS >

C

D

F

G

H

I

J

K

L

M

A

B

WT

N

O

P

TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED

Description

INFOID:0000000010715113

The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.

Diagnosis Procedure

INFOID:0000000010715114

1.

CHECK TIRE PRESSURE SENSOR INSTALLATION 

Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed. 
• Tire pressure sensor(s) of other cars are installed. 

Are the genuine NISSAN tire pressure sensors are installed correctly? 

YES

>> GO TO 2.

NO

>> Replace and/or Install tire pressure sensor(s). Refer to 

WT-62, "Removal and Installation"

. GO TO

3.

2.

CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL

Check tire pressure sensor activation tool.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-

sor activation tool.

3.

TIRE PRESSURE SENSOR ID REGISTRATION

Perform tire pressure sensor ID registration. Refer to 

WT-30, "Work Procedure"

.

CAUTION:

To perform ID registration, observe the following points:

• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.

Is tire pressure sensor ID registration completed?

YES

>> INSPECTION END

NO

>> GO TO 4.

4.

CHECK TIRE PRESSURE SIGNAL

Change the work location and perform ID registration again.
NOTE:

Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a
poor reception. If an ID registration is performed under this condition, the registration may not be completed.
In such case, follow the instructions below to improve the radio wave receiving environment.

• Rotate tire by 90

°

, 180

°

, or 270

°

. (This step is to change tire pressure sensor position.)

• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?

All wheels react and ID registration is possible.>>INSPECTION END
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to 

WT-62, "Removal and

Installation"

.

All wheels do not react.>>Replace the BCM. Refer to 

BCS-121, "Removal and Installation"

.

WT-56

< SYMPTOM DIAGNOSIS >

HAZARD WARNING LAMP REMAINS ON

HAZARD WARNING LAMP REMAINS ON

Description

INFOID:0000000010715115

The hazard warning lamp remains on.

Diagnosis Procedure

INFOID:0000000010715116

1.

CHECK HAZARD WARNING LAMP OPERATION

Check hazard warning lamp operation with hazard switch.

Is the operation normal?

YES

>> Replace the BCM. Refer to 

BCS-121, "Removal and Installation"

.

NO

>> Perform trouble diagnosis for the hazard warning lamp. Refer to 

EXL-174, "Diagnosis Procedure"

(LED headlamp), 

EXL-358, "Diagnosis Procedure"

 (halogen headlamp).