Nissan X-Trail 32. Manual - part 2152

TM-566

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

U1117 LOST COMMUNICATION (ABS)

U1117 LOST COMMUNICATION (ABS)

DTC Description

INFOID:0000000010622789

DTC DETECTION LOGIC

POSSIBLE CAUSE

• ABS actuator and electric unit (control unit)
• Harness or connector (CAN communication line is open or shorted)

FAIL-SAFE

• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Start the engine and wait for 5 seconds or more.

2.

Check the DTC.

Is “U1117” detected?

YES

>> Go to 

TM-566, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010622790

For the diagnosis procedure, refer to 

LAN-17, "Trouble Diagnosis Flow Chart"

. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

U1117

LOST COMM (ABS)
(Lost Communication With ABS)

When the ignition switch is ON, TCM is unable to receive the CAN com-
munications signal from ABS actuator and electric unit (control unit) con-
tinuously for 2 seconds or more.

P062F EEPROM

TM-567

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P062F EEPROM

DTC Description

INFOID:0000000010622791

TCM compares the calculated value stored in the flash ROM with the value stored in TCM. If the calculated
value does not agree with the stored value, TCM judges this as a malfunction.

DTC DETECTION LOGIC

POSSIBLE CAUSE

• TCM (Flash ROM)
• Harness or connector [TCM power supply (back-up) circuit is open or shorted]

FAIL-SAFE

• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine.

2.

Check the DTC.

Is “P062F” detected?

YES

>> Go to 

TM-567, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010622792

1.

REPLACE TCM

Replace the TCM. Refer to 

TM-676, "Removal and Installation"

.

>> WORK END

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P062F

EEPROM
(Internal Control Module EEPROM Error)

Flash ROM error is detected when turning ON the ignition switch.

TM-568

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0705 TRANSMISSION RANGE SENSOR A

P0705 TRANSMISSION RANGE SENSOR A

DTC Description

INFOID:0000000010622793

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector (Short circuit between transmission range switch and TCM)
• Transmission range switch

FAIL-SAFE

• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start  is  slow
• Acceleration is slow
• Lock-up is not performed
• Stop/start system prohibited
• Restart the engine during the stop/start system operation
• Turn OFF the electric oil pump relay

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Turn ignition switch ON.

2.

Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
5 seconds or more.)

3.

Check the first trip DTC.

Is “P0705” detected?

YES

>> Go to 

TM-568, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010622794

1.

CHECK TCM INPUT SIGNALS

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Data Monitor” in “TRANSMISSION”.

3.

Select “D POSITION SW”, “N POSITION SW”, “R POSITION SW”, and “P POSITION SW”.

4.

Shift the selector lever through entire positions from “P” to “D” and check ON/OFF of each monitor item. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0705

T/M RANGE SENSOR A
[Transmission Range Sensor A Circuit (PRNDL 
Input)]

When all of the following conditions are satisfied and this state is main-
tained for 2 seconds:
• Two or more range signals simultaneously stay ON continuously
• TCM power supply voltage: More than 11 V

Monitor item

Condition

Condition

D POSITION SW

Selector lever: “D” position

On

Other than the above

Off

P0705 TRANSMISSION RANGE SENSOR A

TM-569

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Without CONSULT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Turn ignition switch ON.

4.

Shift the selector lever from “P” to “D” and check voltage between TCM harness connector terminals and
ground. 

Is the inspection result normal?

YES >> INSPECTION 

END

NO-1 [“D POSITION SW” is “ON” when selector is not in “D” position. (Or connector terminal 4 is at power
voltage.)]>>GO TO 2.
NO-2 [“N POSITION SW” is “ON” when selector is not in “N” position. (Or connector terminal 5 is at power
voltage.)]>>GO TO 4.
NO-3 [“R POSITION SW” is “ON” when selector is not in “R” position. (Or connector terminal 6 is at power
voltage.)]>>GO TO 6.
NO-4 [“P POSITION SW” is “ON” when selector is not in “P” position. (Or connector terminal 7 is at power
voltage.)]>>GO TO 8.

2.

CHECK D POSITION SW CIRCUIT (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace malfunctioning parts.

N POSITION SW

Selector lever: “N” position

On

Other than the above

Off

R POSITION SW

Selector lever: “R” position

On

Other than the above

Off

P POSITION SW

Selector lever: “P” position

On

Other than the above

Off

+

−

Condition

Voltage

TCM

Connector

Terminal

F119

4

Ground

Selector lever: “D” position

10 – 16 V

Other than the above

Approx. 0 V

5

Selector lever: “N” position

10 – 16 V

Other than the above

Approx. 0 V

6

Selector lever: “R” position

10 – 16 V

Other than the above

Approx. 0 V

7

Selector lever: “P” position

10 – 16 V

Other than the above

Approx. 0 V

Monitor item

Condition

Condition

TCM

Continuity

Connector

Terminal

F119

4

2

Not existed

5

6

7