Nissan X-Trail 32. Manual - part 2092

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  2090  2091  2092  2093   ..

 

 

Nissan X-Trail 32. Manual - part 2092

 

 

TM-326

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0705 TRANSMISSION RANGE SENSOR A

Check continuity between transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

450, "Removal and Installation"

.

Transmission range switch

Condition

Continuity

Terminal

1 – 2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3 – 4

Manual lever: “P” position

Existed

Other than the above

Not existed

3 – 5

Manual lever: “R” position

Existed

Other than the above

Not existed

3 – 6

Manual lever: “N position

Existed

Other than the above

Not existed

3 – 7

Manual lever: “D” position

Existed

Other than the above

Not existed

P0706 TRANSMISSION RANGE SENSOR A

TM-327

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0706 TRANSMISSION RANGE SENSOR A

DTC Description

INFOID:0000000010622515

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector (Open circuit between ignition switch and transmission range switch/open circuit

between transmission range switch and TCM)

• Transmission range switch
• Control cable
Harness or connector (CAN communication line is error)

FAIL-SAFE

• Shift position indicator on combination meter is not displayed
• Selector shock is large
• Start  is  slow
• Acceleration is slow
• Lock-up is not performed

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
40 seconds or more.)

3.

Check the first trip DTC.

Is “P0706” detected?

YES

>> Go to 

TM-327, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010622516

1.

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to 

TM-308, "Adjustment"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Results” in “TRANSMISSION”.

3.

Touch “Erase”.

4.

Perform “DTC CONFIRMATION PROCEDURE". Refer to 

TM-288, "DTC Index"

.

Is “P0706” detected?

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0706

T/M RANGE SENSOR A
(Transmission Range Sensor A Circuit Range/
Performance)

When all of the following conditions are satisfied and this state is main-
tained for 30 seconds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V

TM-328

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0706 TRANSMISSION RANGE SENSOR A

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK POWER CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect transmission range switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between transmission range switch harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 7.

4.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between transmission range switch harness connector terminals and TCM harness con-
nector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (PART 2) 

Check continuity between transmission range switch harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to 

TM-329, "Component Inspection"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH

+

Voltage

Transmission range switch

Connector

Terminal

F22

3

Ground

10 – 16 V

Transmission range switch

TCM

Continuity

Connector

Terminal

Connector

Terminal

F22

4

F23

7

Existed

5

6

6

5

7

4

Transmission range switch

Continuity

Connector

Terminal

F22

4

Ground

Not existed

5

6

7

P0706 TRANSMISSION RANGE SENSOR A

TM-329

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector terminal and transmission range switch harness
connector terminal.

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to 

PG-52, "Wiring Dia-

gram - IGNITION POWER SUPPLY -"

.

• Short circuit in harness between IPDM E/R harness connector terminal 71 and transmission range switch

harness connector terminal 3.

• 10A fuse (No. 97, located in the IPDM E/R). Refer to 

PG-89, "Fuse, Connector and Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> INSPECTION END

NO

>> Repair or replace malfunctioning parts.

Component Inspection

INFOID:0000000010622517

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

450, "Removal and Installation"

.

IPDM E/R

Transmission range switch

Continuity

Connector

Terminal

Connector

Terminal

F72

71

F22

3

Existed

Transmission range switch

Condition

Continuity

Terminal

1 – 2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3 – 4

Manual lever: “P” position

Existed

Other than the above

Not existed

3 – 5

Manual lever: “R” position

Existed

Other than the above

Not existed

3 – 6

Manual lever: “N position

Existed

Other than the above

Not existed

3 – 7

Manual lever: “D” position

Existed

Other than the above

Not existed

 

 

 

 

 

 

 

содержание   ..  2090  2091  2092  2093   ..