Nissan X-Trail 32. Manual - part 1736

PWC-46

< DTC/CIRCUIT DIAGNOSIS >

REAR POWER WINDOW SWITCH

REAR POWER WINDOW SWITCH 

Component Function Check

INFOID:0000000010735228

1.

 CHECK FUNCTION

Check rear power window motor (LH/RH) operation with rear power window switch (LH/RH) and power win-
dow main switch (rear LH/RH switch).

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-46, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010735229

LHD MODELS

1.

CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between rear power window switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and rear power window switch
harness connector.

4.

Check continuity between power window main switch harness connector and ground.

(+)

(

−

)

Condition

Voltage

Rear power window switch

Connector

Terminal 

LH

D83

2

Ground

Power window main 
switch
(rear LH switch)

UP

9 - 16 V

DOWN

0 - 1 V

3

UP

0 - 1 V

DOWN

9 - 16 V

RH

D103

2

Power window main 
switch
(rear RH switch)

UP

9 - 16 V

DOWN

0 - 1 V

3

UP

0 - 1 V

DOWN

9 - 16 V

Power window main switch

Rear power window switch

Continuity

Connector

Terminal

Connector

Terminal

D5

8

LH

D83

3

Existed

9

2

6

RH

D103

3

7

2

REAR POWER WINDOW SWITCH

PWC-47

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-74, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.
Refer to 

PWC-48, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear power window switch. Refer to 

PWC-75, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

RHD MODELS

1.

CHECK REAR POWER WINDOW SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between rear power window switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and rear power window switch
harness connector.

Power window main switch

Ground

Continuity

Connector

Terminal

D5

8

Not existed

9

6

7

(+)

(

−

)

Condition

Voltage

Rear power window switch

Connector

Terminal 

LH

D113

2

Ground

Power window main 
switch
(rear LH switch)

UP

9 - 16 V

DOWN

0 - 1 V

3

UP

0 - 1 V

DOWN

9 - 16 V

RH

D93

2

Power window main 
switch
(rear RH switch)

UP

9 - 16 V

DOWN

0 - 1 V

3

UP

0 - 1 V

DOWN

9 - 16 V

PWC-48

< DTC/CIRCUIT DIAGNOSIS >

REAR POWER WINDOW SWITCH

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-74, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.
Refer to 

PWC-48, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace rear power window switch. Refer to 

PWC-75, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-44, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000010735230

1.

CHECK REAR POWER WINDOW SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect rear power window switch connector.

3.

Check rear power window switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace rear power window switch. Refer to 

PWC-75, "Removal and Installation"

.

Power window main switch

Rear power window switch

Continuity

Connector

Terminal

Connector

Terminal

D25

8

LH

D113

3

Existed

9

2

6

RH

D93

3

7

2

Power window main switch

Ground

Continuity

Connector

Terminal

D25

8

Not existed

9

6

7

Rear power window switch

Condition

Continuity

Terminal

1

5

UP

Existed

3

4

3

4

NEUTRAL

2

5

1

4

DOWN

2

5

POWER WINDOW MOTOR

PWC-49

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

POWER WINDOW MOTOR

DRIVER SIDE

DRIVER SIDE : Component Function Check

INFOID:0000000010735231

1.

 CHECK FUNCTION

Check front power window motor (driver side) operation with power window main switch.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

PWC-49, "DRIVER SIDE : Diagnosis Procedure"

.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000010735232

LHD MODELS

1.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window motor (driver side) connector.

3.

Turn ignition switch ON.

4.

Check voltage between front power window motor (driver side) harness connector and ground.

Is the inspection result normal?

YES

>> Replace front power window motor (driver side). Refer to 

GW-47, "Removal and Installation"

.

NO

>> GO TO 2.

2.

CHECK FRONT POWER WINDOW MOTOR (DRIVER SIDE) CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch harness connector and front power window motor
(driver side) harness connector.

4.

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace power window main switch. Refer to 

PWC-74, "POWER WINDOW MAIN SWITCH :

Removal and Installation"

.

NO

>> Repair or replace harness.

(+)

(

−

)

Condition

Voltage

Front power window motor (driver side)

Connector

Terminal

D7

2

Ground

Power window main 
switch

UP

9 – 16 V

DOWN

0 – 1 V

3

UP

0 – 1 V

DOWN

9 – 16 V

 Power window main switch

Front power window motor (driver side)

Continuity

Connector

Terminal

Connector

Terminal

D6

17

D7

2

Existed

19

3

Power window main switch

Ground

Continuity

Connector

Terminal

D6

17

Not existed

19