Nissan X-Trail 32. Manual - part 159

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  157  158  159  160   ..

 

 

Nissan X-Trail 32. Manual - part 159

 

 

BRC-102

< BASIC INSPECTION >

[WITH VDC (ESP)]

CALIBRATION OF DECEL G SENSOR

CALIBRATION OF DECEL G SENSOR

Description

INFOID:0000000010723658

CAUTION:

Always perform the decel G sensor calibration before driving when the following operation is per-
formed.
NOTE:
Yaw rate/side/decel G sensor calibration is performed when performing the decel G sensor calibration.

×

: Required —: Not required

Work Procedure

INFOID:0000000010723659

Decel G sensor calibration

CAUTION:

Always use CONSULT for the decel G sensor calibration. (It cannot be adjusted other than with CON-
SULT.) 
NOTE:
Yaw rate/side/decel G sensor calibration is performed when performing the decel G sensor calibration.

1.

CHECK THE VEHICLE STATUS

1.

Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

2.

Stop the engine.

3.

Turn the ignition switch OFF.

Is the vehicle stopped in the straight-ahead position on level surface?

YES

>> GO TO 2.

NO

>> Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

2.

PERFORM DECEL G SENSOR CALIBRATION

CAUTION:

• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start engine.

2.

Select “ABS”, “WORK SUPPORT”, “DECEL G SENSOR CALIBRATION” in this order.

3.

Select “START”.

4.

After approx. 10 seconds, select “END”.

5.

Turn ignition switch OFF and then turn it ON again.

CAUTION:

Be sure to perform the operation above.

>> GO TO 3.

Procedure

Decel G sensor calibration

Removing/ installing ABS actuator and electric unit (control unit)

×

Replacing ABS actuator and electric unit (control unit)

×

Removing/installing steering components

Replacing steering components

Removing/installing suspension components

Replacing suspension components

Removing/installing tire

Replacing tire

Tire rotation

Adjusting wheel alignment.

CALIBRATION OF DECEL G SENSOR

BRC-103

< BASIC INSPECTION >

[WITH VDC (ESP)]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

3.

CHECK DATA MONITOR

With CONSULT

1.

Drive the vehicle. Steer the steering wheel to the straight-ahead position. Stop the vehicle on level sur-
face.

2.

Select “ABS”, “DATA MONITOR”, “ECU INPUT SIGNALS” and “DECEL G SENSOR” in this order. Check
that the signal is within the specified value.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 1.

4.

ERASE SELF-DIAGNOSIS MEMORY

With CONSULT

Erase self-diagnosis result of “ABS”.

Are the memories erased?

YES

>> End of work.

NO

>> Check the items indicated by the self-diagnosis.

DECEL G SENSOR

: Approx. 

±

0.08 G

BRC-104

< BASIC INSPECTION >

[WITH VDC (ESP)]

CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]

CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]

Work Procedure

INFOID:0000000010723660

CAUTION:

• Use “Manual Configuration” only when “TYPE ID” of ABS actuator and electric unit (control unit)

cannot be read.

• After configuration, turn the ignition switch from OFF to ON and check that the VDC warning lamp

turns OFF after staying illuminated for approximately two seconds.

• If an error occurs during configuration, start over from the beginning.

1.

CHECKING TYPE ID (1)

Use FAST (service parts catalogue) to search ABS actuator and electric unit (control unit) of the applicable
vehicle and find “Type ID”.

Is “Type ID” displayed?

YES

>> Print out “Type ID” and GO TO 2.

NO

>>

“Configuration” is not required for ABS actuator and electric unit (control unit). Replace in the
usual manner.

• LHD models: Refer to 

BRC-217, "LHD : Removal and Installation"

.

• RHD models: Refer to 

BRC-220, "RHD : Removal and Installation"

.

2.

CHECKING TYPE ID (2)

CONSULT Configuration

1.

Select “Before Replace ECU” of “Read/Write Configuration”.

2.

Check that “Type ID” is displayed on the CONSULT screen.

Is “Type ID” displayed?

YES

>> GO TO 3.

NO

>> GO TO 7.

3.

VERIFYING TYPE ID (1)

CONSULT Configuration

Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 4.

4.

SAVING TYPE ID

CONSULT Configuration

Save “Type ID” on CONSULT.

>> GO TO 5.

5.

REPLACING ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (1)

Replace the ABS actuator and electric unit (control unit).
• LHD models: Refer to 

BRC-217, "LHD : Removal and Installation"

.

• RHD models: Refer to 

BRC-220, "RHD : Removal and Installation"

.

CAUTION:

Never perform the following work items:
• Air bleeding
• Adjustment of steering angle sensor neutral position
• Calibration of decel G sensor

>> GO TO 6.

6.

WRITING (AUTOMATIC WRITING)

CONFIGURATION [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)]

BRC-105

< BASIC INSPECTION >

[WITH VDC (ESP)]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

CONSULT Configuration

1.

Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.

2.

Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the ABS actuator and electric unit (control unit).
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

7.

REPLACING ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) (2)

Replace the ABS actuator and electric unit (control unit).
• LHD models: Refer to 

BRC-217, "LHD : Removal and Installation"

.

• RHD models: Refer to 

BRC-220, "RHD : Removal and Installation"

.

CAUTION:

Never perform the following work items:
• Air bleeding
• Adjustment of steering angle sensor neutral position
• Calibration of decel G sensor

>> GO TO 8.

8.

WRITING (MANUAL WRITING)

CONSULT Configuration

1.

Select “Manual Configuration”.

2.

Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the ABS
actuator and electric unit (control unit).
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 9.

9.

VERIFYING TYPE ID (2)

Compare “Type ID” written into the ABS actuator and electric unit (control unit) with the one searched by using
FAST (service parts catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.

>> GO TO 10.

10.

CHECKING VDC WARNING LAMP

1.

Turn the ignition switch OFF.

2.

Turn the ignition switch ON and check that the VDC warning lamp turns OFF after staying illuminated for
approximately two seconds.

CAUTION:

Never start the engine.

Is the inspection result normal?

YES

>> GO TO 11.

NO

>> Perform the self-diagnosis of “ABS”.

11.

PERFORMING SUPPLEMENTARY WORK

1.

Perform the air bleeding.

-

LHD: Refer to 

BR-14, "Bleeding Brake System"

.

-

RHD: Refer to 

BR-78, "Bleeding Brake System"

.

2.

Perform the adjustment of steering angle sensor neutral position. Refer to 

BRC-99, "Work Procedure"

.

3.

Perform the calibration of decel G sensor. Refer to 

BRC-102, "Work Procedure"

.

4.

Perform the self-diagnosis of all systems.

5.

Record or print self-diagnosis result and freeze frame data (FFD).

6.

Erase self-diagnosis results.

 

 

 

 

 

 

 

содержание   ..  157  158  159  160   ..