Nissan X-Trail 32. Manual - part 1219

HEADLAMP (LO) CIRCUIT

EXL-333

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK HEADLAMP (LO) BULB

Check the applicable headlamp (LO) bulb.

Is the inspection result normal?

YES

>> Check the corresponding headlamp (LO) harness. Repair or replace if necessary.

NO

>> Replace the corresponding headlamp (LO) bulb. Refer to 

EXL-376, "Replacement"

.

Front combination lamp

—

Continuity

Connector

Terminal

RH

E152

8

Ground

Existed

LH

E154

EXL-334

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

PARKING LAMP CIRCUIT

PARKING LAMP CIRCUIT

Component Function Check

INFOID:0000000010789859

1.

CHECK PARKING LAMP OPERATION

With CONSULT

1.

Select “PARKING LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the parking lamp is turned ON.

Is the inspection result normal?

YES

>> Parking lamp circuit is normal.

NO

>> Refer to 

EXL-334, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010789860

1.

CHECK PARKING LAMP OUTPUT VOLTAGE

With CONSULT

1.

Turn ignition switch OFF.

2.

Disconnect front combination lamp connector.

3.

Turn ignition switch ON.

4.

Select “PARKING LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

5.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-60, "Removal and Installation"

.

2.

CHECK PARKING LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and front combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK PARKING LAMP GROUND CIRCUIT

Check continuity between front combination lamp harness connector and ground.

On

: Parking lamp ON

Off

: Parking lamp OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E149

61

Ground

PARKING LAMP

On

9 – 16 V

Off

0 – 1 V

LH

E148

56

On

9 – 16 V

Off

0 – 1 V

IPDM E/R

Front combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E149

61

E151

3

Existed

LH

E148

56

E153

PARKING LAMP CIRCUIT

EXL-335

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> Replace the corresponding front combination lamp. Refer to 

EXL-376, "Removal and Installation"

.

NO

>> Repair or replace harness.

Front combination lamp

—

Continuity

Connector

Terminal

RH

E151

2

Ground

Existed

LH

E153

EXL-336

< DTC/CIRCUIT DIAGNOSIS >

[HALOGEN HEADLAMP]

TAIL LAMP CIRCUIT

TAIL LAMP CIRCUIT

Component Function Check

INFOID:0000000010789861

1.

CHECK TAIL LAMP OPERATION

With CONSULT

1.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the tail lamp is turned ON.

Is the inspection result normal?

YES

>> Tail lamp circuit is normal.

NO

>> Refer to 

EXL-336, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010789862

1.

CHECK TAIL LAMP OUTPUT VOLTAGE

With CONSULT

1.

Turn ignition switch OFF.

2.

Disconnect the following connectors.

-

Rear combination lamp LH (body side)

-

Rear combination lamp RH (body side)

-

Rear combination lamp LH (back door side)

-

Rear combination lamp RH (back door side)

3.

Turn ignition switch ON.

4.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

5.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-60, "Removal and Installation"

.

2.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and each rear combination lamp harness con-
nector.

Body side

On

: Tail Lamp ON

Off

: Tail lamp OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E10

17

Ground

TAIL LAMP

On

9 – 16 V

Off

0 – 1 V

LH

4

On

9 – 16 V

Off

0 – 1 V

IPDM E/R

Rear combination lamp (body side)

Continuity

Connector

Terminal

Connector

Terminal

RH

E10

17

B59

1

Existed

LH

4

B80