Nissan X-Trail 32. Manual - part 67

 

  Главная      Nissan     Nissan X-Trail 32 - Service Manual

 

поиск по сайту            

 

 

 

 

 

 

 

 

 

содержание   ..  65  66  67  68   ..

 

 

Nissan X-Trail 32. Manual - part 67

 

 

AV-260

< SYMPTOM DIAGNOSIS >

[WITH NAVIGATION]

NORMAL OPERATING CONDITION

RELATED TO HANDS-FREE PHONE

RELATED TO TELEPHONE

Symptom

Possible cause

Possible solution

The traffic information is 
not displayed

The traffic information is not set to on.

Set the traffic information to on.

You are in an area where traffic information is not avail-
able

Scroll to an area where traffic information is avail-
able

The map scale is set at a level where the display of icons 
is impossible.

Check that the map scale is set at a level in which 
the display of icons is possible. 

With the automatic de-
tour route search ON, 
no detour route is set to 
avoid congested areas.

There is no faster route compared to the current route, 
based on the road network and traffic information.

The automatic detour search is not intended for 
avoiding traffic jams. It searches for the fasted 
rote taking into consideration such things as traffic 
jams.

The route does not 
avoid road section with 
traffic information stat-
ing it is closed due to 
road construction.

The navigation system is designed not to avoid this 
event because the actual period of closure may differ 
from the declared roadwork period. 

Observe the actual road condition and follow the 
instructions on road for detour when necessary. If 
the road closure is for certain, use detour function 
and set the detour distance to avoid the closed 
road section.

Traffic information dis-
played differs from in-
formation from other 
media (e.g. radio).

Other media may use different information sources.

Observe the actual road conditions and regula-
tions. Always observe safe driving practices and 
follow all traffic regulations.

Symptom

Cause and Counter measure

Cannot use hands-free phone

Customer will not be able to use a hands-free phone under the fol-
lowing conditions.
• The vehicle is outside of the telephone service area.
• The vehicle is in an area where it is difficult to receive radio 

waves; such as in a tunnel, in an underground parking garage, 
near a tall building or in a mountainous area.

• The cellular phone is locked to prevent it from being dialed.
NOTE:

While a cellular phone is connected through the Bluetooth

®

 wire-

less connection, the battery power of the cellular phone may dis-

charge quicker than usual. The Bluetooth

®

 Hands-Free Phone 

System cannot charge cellular phones.

The other party's voice cannot be heard by hands-free phone.

When the radio wave condition is not ideal or ambient sound is too 
loud, it may be difficult to hear the other person's voice during a 
call.

Poor sound quality

Do not place the cellular phone in an area surrounded by metal or 
far away from the in-vehicle phone module to prevent tone quality 
degradation and wireless connection disruption.

Symptoms

Cause and Counter measure

System fails to interpret the com-
mand correctly.

1. Ensure that the command format is valid.

2. Ensure that the command is spoken after the tone.

3. Speak clearly without pausing between words and at a level appropriate to the ambient noise 
level in the vehicle.

4. Ensure that the ambient noise level is not excessive (for example, windows open or defroster 
on).
NOTE:
 If it is too noisy to use the phone, it is likely that the voice commands will not be recognized.

5. If more than one command was said at a time, try saying the commands separately.

6. If the system consistently fails to recognize commands, the voice training procedure should be 
carried out to improve the recognition response for the speaker.
Refer to 

AV-96, "On Board Diagnosis Function"

.

AV

NORMAL OPERATING CONDITION

AV-261

< SYMPTOM DIAGNOSIS >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

The system consistently selects 
the wrong entry from the phone 
book.

1. Ensure that the phone book entry name requested matches what was originally stored. This 
can be confirmed by using the “List Names” command.

2. Replace one of the names being confused with a new name.

Symptoms

Cause and Counter measure

AV-262

< REMOVAL AND INSTALLATION >

[WITH NAVIGATION]

NAVI CONTROL UNIT

REMOVAL AND INSTALLATION

NAVI CONTROL UNIT

Removal and Installation

INFOID:0000000010714916

REMOVAL

CAUTION:

• The auto ACC function allows the accessory power supply for a certain period of time even after

ignition switch OFF. For this reason, when performing diagnosis, turn the ignition switch OFF and
wait for 3 minutes with the driver's door opened.

• The operation of the vehicle during standby may cause an accessory power supply.
• Before replacing NAVI control unit, perform “Read/Write Configuration” to save or print current vehi-

cle specification. For details, refer to 

AV-157, "ADDITIONAL SERVICE WHEN REPLACING NAVI CON-

TROL UNIT : Description"

.

1.

Remove instrument finisher B. Refer to 

IP-13, "Exploded View"

 (LHD models), 

IP-40, "Exploded View"

(RHD models).

2.

Remove instrument finisher E. Refer to 

IP-13, "Exploded View"

 (LHD models), 

IP-40, "Exploded View"

(RHD models).

3.

Remove A/C control. Refer to 

HAC-125, "Removal and Installation"

 (automatic air conditioning), 

HAC-

222, "Removal and Installation"

 (manual air conditioning).

4.

Remove the NAVI control unit screws, then pull out the NAVI control unit.

5.

Disconnect the harness connectors from the NAVI control unit and remove.

6.

Remove the NAVI control unit bracket screws and the NAVI control unit brackets.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

Be sure to perform “Read/Write Configuration” when replacing NAVI control unit. For details, refer to

AV-157, "CONFIGURATION (NAVI CONTROL UNIT) : Work Procedure"

.

AV

FRONT DOOR SPEAKER

AV-263

< REMOVAL AND INSTALLATION >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

FRONT DOOR SPEAKER

Removal and Installation

INFOID:0000000010714917

REMOVAL

1.

Remove the front door finisher. Refer to 

INT-14, "Removal and Installation"

.

2.

Remove the front door speaker screws 

.

3.

Disconnect the harness connector from the front door speaker
and remove.

INSTALLATION

Install in the reverse order of removal.

JSNIA6727ZZ

 

 

 

 

 

 

 

содержание   ..  65  66  67  68   ..