Nissan X-Trail 32. Manual - part 59

AV-228

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

U1302 CAMERA POWER VOLT

LHD models without BSW

RHD models with BSW

RHD models without BSW

Is the inspection result normal?

YES

>> GO TO 13.

NO

>> Replace around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

.

13.

CHECK SIDE CAMERA LH POWER SUPPLY (2)

1.

Turn ignition switch OFF.

2.

Connect following harness connector.

-

Door mirror (driver side) (LHD models)

-

Door mirror (passenger side) (RHD models)

3.

Turn ignition switch ON.

4.

Check the voltage between around view monitor control unit terminals.

LHD models with BSW

LHD models without BSW

RHD models with BSW

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M24

30

29

6.0 V

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M102

62

64

6.0 V

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M24

34

33

6.0 V

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M102

56

58

6.0 V

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M24

30

29

6.0 V

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M102

62

64

6.0 V

AV

U1302 CAMERA POWER VOLT

AV-229

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

RHD models without BSW

Is the inspection result normal?

YES

>> Replace around view monitor control unit. Refer to 

AV-268, "Removal and Installation"

.

NO

>> Replace side camera RH. Refer to 

AV-271, "Removal and Installation"

.

Around view monitor control unit

Reference value

(Approx.)

Connector

Terminals

+

–

Terminal

M24

34

33

6.0 V

AV-230

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

U1304 CAMERA IMAGE CALIBRATION

U1304 CAMERA IMAGE CALIBRATION

DTC Description

INFOID:0000000010714889

DTC DETECTION LOGIC

POSSIBLE CAUSE

Perform camera calibration

FAIL-SAFE

Unmatched icon 

 display (red) is displayed (applicable for unmatched camera only).

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

WITH CONSULT

1.

Turn the ignition switch ON.

2.

Turn ignition switch OFF and wait at least 30 seconds.

3.

Turn ignition switch ON and wait at least 30 seconds or more.

4.

Select “Self Diagnostic Result” mode of “AVM” using CONSULT.

5.

Check DTC.

Is DTC U1304 detected?

YES

>> Refer to 

AV-230, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010714890

1.

PERFORM CALIBRATING CAMERA IMAGE

Perform camera calibration when DTC U1304 is detected.

>> Perform camera calibration. Refer to 

AV-161, "CALIBRATING CAMERA IMAGE (AROUND VIEW

MONITOR) : Description"

.

DTC

Trouble diagnosis

(Trouble diagnosis contents)

Detection condition

U1304

CAMERA IMAGE CALIB
(Camera image calibration)

Camera calibration is incomplete.
NOTE:
Current malfunction is displayed only and is not saved.

AV

U1305 CONFIG UNFINISH

AV-231

< DTC/CIRCUIT DIAGNOSIS >

[WITH NAVIGATION]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

U1305 CONFIG UNFINISH

DTC Description

INFOID:0000000010923284

DTC DETECTION LOGIC

POSSIBLE CAUSE

Vehicle specifications for around view monitor control unit is incomplete

FAIL-SAFE

• On applicable camera screen 

 marking (Red) is displayed.

• Around view monitor with Park Assist is cancel.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

WITH CONSULT

1.

Turn the ignition switch ON.

2.

Turn ignition switch OFF and wait at least 30 seconds.

3.

Turn ignition switch ON and wait at least 30 seconds or more.

4.

Select “Self Diagnostic Result” mode of “AVM” using CONSULT.

5.

Check DTC.

Is DTC U1305 detected?

YES

>> Refer to 

AV-231, "Diagnosis Procedure"

.

NO-1

>> To check malfunction symptom before repair: Refer to 

GI-44, "Intermittent Incident"

.

NO-2

>> Confirmation after repair: INSPECTION END

Diagnosis Procedure

INFOID:0000000010923285

1.

PERFORM CONFIGURATION OF AROUND VIEW MONITOR CONTROL UNIT

Perform configuration of around view monitor control unit when DTC U1305 is detected.

>> Perform configuration of around view monitor control unit. Refer to 

AV-159, "CONFIGURATION

(AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure"

.

DTC

Trouble diagnosis

(Trouble diagnosis contents)

Detecting condition

U1305

CONFIG UNFINISH
(Configuration unfinish)

The vehicle specifications of around view monitor control unit is incomplete.
NOTE:
Current malfunction is displayed only and is not saved.