Nissan Qashqai J11. Manual - part 919

PB-58

< BASIC INSPECTION >

RELEASE OF REAR BRAKE CALIPER

RELEASE OF REAR BRAKE CALIPER

Description

INFOID:0000000010833871

CAUTION:

When the following operations are performed, always use CONSULT, for performing “BRAKE
RELEASE” of “WORK SUPPORT”.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833872

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to 

PB-47, "Work Procedure"

.

1.

PERFORM BRAKE OPERATION

With CONSULT

1.

Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.

CAUTION:

• Never operate the parking brake switch.
• Never depress the brake pedal.

2.

Touch “START”.

>> GO TO 2.

2.

PERFORM BRAKE RELEASE

With CONSULT

1.

Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.

CAUTION:

• Never operate the parking brake switch.
• Never depress the brake pedal.

Procedure

BRAKE RELEASE

Removing/installing electric parking brake control module

×

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

×

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

×

Replacing rear brake pad

×

Removing/installing rear brake caliper assembly

×

Replacing rear brake caliper assembly

×

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

CHANGE OF SYSTEM MODE

PB-59

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

CHANGE OF SYSTEM MODE

Description

INFOID:0000000010833873

CAUTION:

When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE
CHANGE” of “WORK SUPPORT”.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833874

CAUTION:

When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module

1.

CONFIGURATION

Perform the configuration. Refer to 

PB-41, "Work Procedure"

.

>> GO TO 2.

2.

CALIBRATION OF G SENSOR

Perform the calibration of G sensor. Refer to 

PB-51, "Work Procedure"

.

>> GO TO 3.

3.

RESET OF CLUTCH PEDAL STROKE SENSOR

Perform the reset of clutch stroke sensor. Refer to 

PB-53, "Work Procedure"

.

>> GO TO 4.

4.

ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION

Perform the adjustment of rear brake caliper initial position: Refer to 

PB-49, "Work Procedure"

.

>> GO TO 5.

5.

OPERATION OF REAR BRAKE CALIPER

Perform the operation of rear brake caliper: Refer to 

PB-55, "Work Procedure"

.

>> GO TO 6.

6.

RELEASE OF REAR BRAKE CALIPER

Perform the release of rear brake caliper: Refer to 

PB-57, "Work Procedure"

.

Procedure

SYSTEM MODE CHANGE

Removing/installing electric parking brake control module

—

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

PB-60

< BASIC INSPECTION >

CHANGE OF SYSTEM MODE

CHANGE OF SYSTEM MODE

Description

INFOID:0000000010833873

CAUTION:

When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE
CHANGE” of “WORK SUPPORT”.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833874

CAUTION:

When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module

1.

CONFIGURATION

Perform the configuration. Refer to 

PB-42, "Work Procedure"

.

>> GO TO 2.

2.

CALIBRATION OF G SENSOR

Perform the calibration of G sensor. Refer to 

PB-52, "Work Procedure"

.

>> GO TO 3.

3.

RESET OF CLUTCH PEDAL STROKE SENSOR

Perform the reset of clutch stroke sensor. Refer to 

PB-54, "Work Procedure"

.

>> GO TO 4.

4.

ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION

Perform the adjustment of rear brake caliper initial position: Refer to 

PB-50, "Work Procedure"

.

>> GO TO 5.

5.

OPERATION OF REAR BRAKE CALIPER

Perform the operation of rear brake caliper: Refer to 

PB-56, "Work Procedure"

.

>> GO TO 6.

6.

RELEASE OF REAR BRAKE CALIPER

Perform the release of rear brake caliper: Refer to 

PB-58, "Work Procedure"

.

Procedure

SYSTEM MODE CHANGE

Removing/installing electric parking brake control module

—

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE

PB-61

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

DTC/CIRCUIT DIAGNOSIS

C10C8 ELECTRIC PARKING BRAKE CONTROL MODULE

DTC Description

INFOID:0000000010833649

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Harness or connector
• Electric parking brake control module
• Parking brake switch

FAIL-SAFE

Type 1

Only mechanical release is available.

Type 2

Only mechanical release is available.

Type 3

Only mechanical release is available.

Type 4

Only mechanical release is available.

Type 5

Automatic apply and release are prohibited.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1.

Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait for 10 seconds after turning ignition switch OFF or ON.

2.

Push the parking brake switch.

CAUTION:

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

Type

C10C8

CONTROL MODULE
(CONTROL MODULE)

INTERNAL ELECTRIC 
MALFNCTN
(INTERNAL ELECTRIC 
MALFNCTN)

When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of hardware)

1

WATCHDOG/SAFETY 

µ

C 

ERROR
(Watchdog/safety 

µ

C error)

When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of communica-
tion)

2

SUPERVISION SOFT-
WARE ERROR
(Supervision software error)

When there is an internal malfunction in the electric park-
ing brake control module. (Malfunction of software)

3

EVENT INFORMATION
(Event information)

When there is an internal malfunction in the electric park-
ing brake control module. (Maintenance mode)

4

NOT CONFIGURED
(Not configured)

When variant coding is incomplete.

5