Nissan Qashqai J11. Manual - part 803

DLN-128

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY30A]

LOCK INDICATOR LAMP

LOCK INDICATOR LAMP

Description

INFOID:0000000010288304

The following is the indications of indicator lamp after engine start.

AWDAWD INDICATOR LAMP AND LOCK INDICATOR LAMP

Diagnosis Procedure

INFOID:0000000010288305

1.

CHECK AWD WARNING LAMP

Start engine and drive at 30 km/h (19 MPH) or more for approx. 1 minute.

Does AWD warning lamp turn ON?

YES

>> Go to 

DLN-126, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK AWD MODE SWITCH

Perform the trouble diagnosis for AWD mode switch. Refer to 

DLN-116, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning part.

3.

CHECK LOCK INDICATOR LAMP SIGNAL

With CONSULT

1.

Start the engine.

CAUTION:

Stop the vehicle.

2.

Change AWD mode switch in “LOCK” from “AUTO”.

3.

Check “AWD MODE MON” of AWD control unit CONSULT “DATA MONITOR”.

Does the item on “DATA MONITOR” indicate “LOCK”?

YES

>> GO TO 4.

NO

>> Replace AWD control unit. Refer to 

DLN-124, "Diagnosis Procedure"

.

4.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Perform the trouble diagnosis for combination meter power supply circuit. Refer to 

MWI-61, "COMBINATION

METER : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Repair or replace the malfunctioning part.

Condition

AWD indicator lamp

LOCK indicator lamp

2WD mode

OFF

OFF

AUTO mode

ON

OFF

LOCK mode

ON

ON

AWD CONTROL UNIT

DLN-129

< ECU DIAGNOSIS INFORMATION >

[TRANSFER: TY30A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

ECU DIAGNOSIS INFORMATION

AWD CONTROL UNIT

Reference Value

INFOID:0000000010288306

VALUES ON THE DIAGNOSIS TOOL

Monitor item

Condition

Value/Status

FR RH SENSOR

Vehicle stopped

0.00 km/h (0.00 mph)

Vehicle running

CAUTION:

Check air pressure of tire under standard condition.

Approximately equal to the indi-
cation on speedometer (Inside 
of 

±

10%)

FR LH SENSOR

Vehicle stopped

0.00 km/h (0.00 mph)

Vehicle running

CAUTION:

Check air pressure of tire under standard condition.

Approximately equal to the indi-
cation on speedometer (Inside 
of 

±

10%)

RR RH SENSOR

Vehicle stopped

0.00 km/h (0.00 mph)

Vehicle running

CAUTION:

Check air pressure of tire under standard condition.

Approximately equal to the indi-
cation on speedometer (Inside 
of 

±

10%)

RR LH SENSOR

Vehicle stopped

0.00 km/h (0.00 mph)

Vehicle running

CAUTION:

Check air pressure of tire under standard condition.

Approximately equal to the indi-
cation on speedometer (Inside 
of 

±

10%)

BATTERY VOLT

Always

Battery voltage

THRTL POS SEN

When depressing accelerator pedal
(Value rises gradually in response to throttle position.)

0 – 100%

ETS SOLENOID

Engine running
• At idle speed

AWDAWD mode switch: 2WD

Approx. 0.000 A

AWD indicator lamp: ON

Approx. 0.000 A

LOCK indicator lamp: ON

Approx. 0.000 A

Engine running
• When depressing accelerator 

pedal

AWD mode switch: 2WD

Approx. 0.000 A

AWD indicator lamp: ON

R9M: Approx. 0.000 – 2.000 A*

LOCK indicator lamp: ON

R9M: Approx. 2.000 A

STOP LAMP SW

Brake pedal: Depressed

On

Brake pedal: Released

Off

ENG SPEED SIG

Engine stopped
(Engine speed: Less than 400 rpm)

Stop

Engine running
(Engine speed: 400 rpm or more)

Run

ETS ACTUATOR

Engine stopped (Ignition switch: ON)

Off

Engine running

On

4WD WARN LAMP

AWD warning lamp: ON

On

AWD warning lamp: OFF

Off

4WD MODE SW

AWD mode switch: 2WD

2WD

AWD mode switch: AUTO

AUTO

AWD mode switch: LOCK
(State of hold of LOCK position)

LOCK

DLN-130

< ECU DIAGNOSIS INFORMATION >

[TRANSFER: TY30A]

AWD CONTROL UNIT

*: The values are changed by throttle opening and engine speed.

TERMINAL LAYOUT

PHYSICAL VALUES

4WD MODE SW

AWD mode switch: 2WD

2WD

AWD mode switch: AUTO

AUTO

AWD mode switch: AUTO 

⇒

 LOCK

(State of AWD indicator lamp turn ON)

AUTO 

⇒

 LOCK

AWD mode switch: AUTO 

⇒

 LOCK

(State of LOCK indicator lamp turn ON)

LOCK 

⇒

 AUTO

DIS-TIRE MONI

Vehicle running with normal size tire installed

0 – 4 mm

Vehicle running with improper size tire installed (Front/rear tire 
size difference, wear condition)

4 – 8 mm, 8 – mm

PARKING BRAKE SW SIG

Parking brake operated

On

Parking brake not operated

Off

Monitor item

Condition

Value/Status

JSDIA0057ZZ

Terminal No.

(Wire color)

Description

Condition

Value (Approx.)

+

-

Signal name

Input/

Output

1

(LG)

Ground

AWD solenoid power sup-
ply

Output

Engine speed: At idle

AWD mode switch: 2WD

0 V

AWD indicator lamp: ON

0 V

LOCK indicator lamp: ON

0 V

Engine speed: 3,000 
rpm or more constant

AWD mode switch: 2WD

0 V

AWD indicator lamp: ON

2.5 V*

LOCK indicator lamp: ON

8 V

2

(L)

Ground

AWD solenoid ground

—

Engine speed: At idle

0 V

Engine speed: 3,000 rpm or more constant

0 V

5

(V)

Ground

AWD mode switch (AUTO)

Output

Ignition switch: ON

AWD mode switch: 2WD

Battery voltage

AWD mode switch: AUTO

0 V

AWD mode switch: LOCK
(State of hold of LOCK position)

0 V

7

(P)

Ground

Ignition switch

Input

Ignition switch: ON

Battery voltage

Ignition switch: OFF

0 V

8

(L)

—

CAN-H

Input/

Output

—

—

9

(G)

Ground

Power supply (AWD sole-
noid)

Input

Ignition switch: ON

Battery voltage

Ignition switch: OFF

Battery voltage

AWD CONTROL UNIT

DLN-131

< ECU DIAGNOSIS INFORMATION >

[TRANSFER: TY30A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

*: The values are changed by throttle opening and engine speed.

CAUTION:

When using circuit tester to measure voltage for inspection, be sure not to extend forcibly any connector terminals.

Wiring Diagram - AWD SYSTEM -

INFOID:0000000010288307

FOR RUSSIA

10

(B)

Ground

Ground

—

Always

0 V

11

(B)

Ground

Ground

—

Always

0 V

12

(BR)

Ground

AWD mode switch (2WD)

Output

Ignition switch: ON

AWD mode switch: 2WD

0 V

AWD mode switch: AUTO

Battery voltage

AWD mode switch: LOCK
(State of hold of LOCK position)

Battery voltage

14

(Y)

Ground

AWD mode switch (LOCK)

Output

Ignition switch: ON

AWD mode switch: 2WD

Battery voltage

AWD mode switch: AUTO

Battery voltage

AWD mode switch: LOCK
(State of hold of LOCK position)

0 V

16

(P)

—

CAN-L

Input/

Output

—

—

Terminal No.

(Wire color)

Description

Condition

Value (Approx.)

+

-

Signal name

Input/

Output