Nissan Qashqai J11. Manual - part 737

P0705 TRANSMISSION RANGE SENSOR A

TM-523

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK N POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK P POSITION SW CIRCUIT (PART 1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK P POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

TCM

Continuity

Connector

Terminal

F1

5

4

Not existed

6

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F1

5

Ground

0 V

TCM

Continuity

Connector

Terminal

F1

7

4

Not existed

5

6

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F1

7

Ground

0 V

TM-524

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0705 TRANSMISSION RANGE SENSOR A

8.

CHECK R POSITION SW CIRCUIT (PART1)

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector.

3.

Check continuity between TCM harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 9.

NO

>> Repair or replace malfunctioning parts.

9.

CHECK R POSITION SW CIRCUIT (PART 2)

1.

Disconnect transmission range switch connector.

2.

Turn ignition switch ON.

3.

Check voltage between TCM harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 10.

NO

>> Repair or replace malfunctioning parts.

10.

CHECK TRANSMISSION RANGE SWITCH

Check transmission range switch. Refer to 

TM-524, "Component Inspection"

.

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

Component Inspection

INFOID:0000000010245601

1.

CHECK TRANSMISSION RANGE SWITCH

Check continuity between transmission range switch connector terminals.

TCM

Continuity

Connector

Terminal

F1

6

4

Not existed

5

7

+

−

Voltage

(Approx.)

TCM

Connector

Terminal

F1

6

Ground

0 V

Transmission range switch

Condition

Continuity

Terminal

1 – 2

Manual lever: “P” and “N” positions

Existed

Other than the above

Not existed

3 – 4

Manual lever: “P” position

Existed

Other than the above

Not existed

3 – 5

Manual lever: “R” position

Existed

Other than the above

Not existed

3 – 6

Manual lever: “N position

Existed

Other than the above

Not existed

3 – 7

Manual lever: “D” position

Existed

Other than the above

Not existed

P0705 TRANSMISSION RANGE SENSOR A

TM-525

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of transmission range switch. Replace transaxle assembly. Refer to 

TM-

629, "Removal and Installation"

.

TM-526

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10G]

P0706 TRANSMISSION RANGE SENSOR A

P0706 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000010245602

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn ignition switch ON.

2.

Shift the selector lever through entire positions from “P” to “D”. (Hold the selector lever at each position for
40 seconds or more.)

3.

Check the first trip DTC.

Is “P0706” detected?

YES

>> Go to 

TM-526, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010245603

1.

ADJUSTMENT OF CONTROL CABLE

Adjust control cable. Refer to 

TM-619, "Inspection"

.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

1.

Turn ignition switch ON.

2.

Select “Self Diagnostic Results” in “TRANSMISSION”.

3.

Touch “Erase”.

4.

Perform “DTC CONFIRMATION PROCEDURE". Refer to 

TM-526, "DTC Logic"

.

Is “P0706” detected?

YES

>> GO TO 3.

NO

>> INSPECTION END

3.

CHECK POWER CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect transmission range switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between transmission range switch harness connector terminal and ground.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0706

T/M RANGE SENSOR A
(Transmission Range Sensor 
A Circuit Range/Performance)

When all of the following conditions are satis-
fied and this state is maintained for 30 sec-
onds:
• All range signals stay OFF
• TCM power supply voltage: More than 11 V

• Harness or connector

(Open circuit between ignition switch 
and transmission range switch/open 
circuit between transmission range 
switch and TCM)

• Transmission range switch
• Control cable