Nissan Qashqai J11. Manual - part 696

P2765 INPUT SPEED SENSOR B

TM-359

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

TM-360

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P2813 SELECT SOLENOID

P2813 SELECT SOLENOID

DTC Logic

INFOID:0000000010589351

DTC DETECTION LOGIC

NOTE:
DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF 

→

 ON 

→

 driv-

ing 

→

 OFF”.

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2813

SELECT SOLENOID
(Select solenoid)

When any of 1, or 2 is satisfied:
1.

When all the following conditions are es-
tablished three times in 1DC

-

Precondition

•

DTC other than the applicable DTC is not 
detected.

•

Throttle position: More than 6.27 deg.

•

Vehicle speed: Less than 3 km/h (1 
MPH)

•

CVT fluid temperature: More than 20

°

C 

(68

°

F)

•

Selector lever: Other than P, N

•

Turbine speed when performed N 

→

 D, 

N (P) 

→

 R: More than 500 rpm

•

TCM power supply voltage: More than 11 
V

-

Detection time

•

N 

→

 D: 0.4 seconds

•

N 

→

 R: 0.3 seconds

•

P 

→

 R: 0.3 seconds

2.

When all of the following conditions are 
satisfied and this state is maintained for 
30 seconds:

-

The counting of time continues while all 
of the following conditions are satisfied 
and stops when the conditions become 
unsatisfied (the count is maintained). 
When accumulated time reaches 30 sec-
onds (Clutch is judged as engaged and 
the count is reset.)

•

Selector lever: Other than P, N

•

Vehicle speed: Less than 3 km/h (1 
MPH)

•

Differences between primary pulley 
speed and secondary speed: Less than 
120 rpm

•

Clutch instructions pressure: 0.95 MPa 
or more

•

Differences between turbine speed and 
input speed: Less than 200 rpm

•

Turbine speed – speed: More than 450 
rpm

•

 DTC other than the applicable DTC is 
not detected.

•

TCM power supply voltage: More than 11 
V

Select solenoid valve

P2813 SELECT SOLENOID

TM-361

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

>> GO TO 2.

2.

CHECK DTC DETECTION 1

1.

Start the engine.

2.

Maintain the following conditions. (Keep 30 seconds or more after the selector lever shifted.)

3.

Check the first trip DTC.

Is “P2813”detected?

YES

>> Go to 

TM-361, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010589352

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-41, "Intermittent Incident"

.

Is the inspection result normal?

YES 

>> Replace transaxle assembly. Refer to 

TM-415, "Removal and Installation"

.

NO

>> Repair or replace malfunctioning parts.

Selector lever

: N

→

 D, N 

→

 R, P

→

 R

TM-362

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P2814 SELECT SOLENOID

P2814 SELECT SOLENOID

DTC Logic

INFOID:0000000010589353

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at
least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1.

Start the engine.

2.

Maintain the following conditions. (Keep 5 seconds or more after the selector lever shifted.)

3.

Check the first trip DTC.

Is “P2814” detected?

YES

>> Go to 

TM-362, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000010589354

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and CVT unit connector.

3.

Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P2814

SELECT SOLENOID
(Select solenoid)

When all of the following conditions are satis-
fied and this state is maintained for 0.48 sec-
onds:
• TCM power supply voltage: 11 V or more
• TCM judges that solenoid valve circuit is 

shorted to ground.

• Harness or connector

(Select solenoid valve circuit shorted to 
ground)

• Select solenoid valve

Selector lever

: N 

→

 D, N 

→

 R, P 

→

 R

TCM

—

Continuity

Connector

Terminal

F2

37

Ground

Not existed

CVT unit

—

Condition

Resistance

Connector

Terminal

F207

4

Ground

CVT fluid temperature: 20

°

C (68

°

F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°

C (122

°

F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°

C (176

°

F)

6.5 – 8.5 

Ω