Nissan Qashqai J11. Manual - part 558

EC9-388

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

LOW PRESSURE FUEL PUMP

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK FUEL PUMP CONTROL CIRCUIT

1.

Disconnect fuel level sensor unit and fuel pump (main) harness connector.

2.

Check the continuity between FPCM harness connector and fuel level sensor unit and fuel pump (main)
harness connector.

3.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts.

5.

CHECK LOW PRESSURE FUEL PUMP

Refer to 

EC9-388, "Component Inspection (Low Pressure Fuel Pump)"

.

Is the inspection result normal?

YES

>> Replace FPCM.

NO

>> Replace low pressure fuel pump.

Component Inspection (Low Pressure Fuel Pump)

INFOID:0000000010500946

1.

CHECK FUEL PRESSURE REGULATOR

1.

Turn ignition switch OFF.

2.

Check low fuel pressure.

Is inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK LOW PRESSURE FUEL PUMP

1.

Turn ignition switch OFF.

2.

Disconnect fuel level sensor unit and fuel pump (main).

3.

Check resistance between fuel level sensor unit and fuel pump (main) terminals as follows.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace fuel level sensor unit and fuel pump (main).

+

−

Continuity

FPCM

Fuel level sensor unit and fuel 

pump (main)

Connector

Terminal

Connector

Terminal

B75

3

B94

1

Existed

4

4

5

3

6

2

+

−

Continuity

Fuel level sensor unit and 

fuel pump (main)

Terminals

2

3

Existed

4

BRAKE SWITCH

EC9-389

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

C

D

E

F

G

H

I

J

K

L

M

A

EC9

N

P

O

BRAKE SWITCH

Component Function Check

INFOID:0000000010309410

1.

CHECK BRAKE SWITCH FUNCTION

1.

Turn ignition switch ON.

2.

Check the voltage between ECM harness connector terminals as per the following.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to 

EC9-389, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010309411

1.

CHECK BRAKE SWITCH POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the voltage between stop lamp switch harness connector and ground.

M/T models

CVT models

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform the trouble diagnosis for power supply circuit.

2.

CHECK BRAKE SWITCH INPUT SIGNAL CIRCUIT

1.

Disconnect ECM harness connector.

2.

Check the continuity between stop lamp switch harness connector and ECM harness connector.

M/T models

ECM

Condition

Voltage

(Approx.)

Connector

+

–

Terminal

E58

17

25

Brake pedal

Slightly de-
pressed

0 V

Fully released

Battery voltage

+

−

Voltage

Stop lamp switch

Connector

Terminal

E50

3

Ground

Battery voltage

+

−

Voltage

Brake pedal position switch

Connector

Terminal

E30

1

Ground

Battery voltage

+

−

Continuity

Stop lamp switch

ECM

Connector

Terminal

Connector

Terminal

E50

4

E58

17

Existed

EC9-390

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

BRAKE SWITCH

CVT models

3.

Also check harness for short to ground and to power.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK BRAKE SWITCH

Check the brake switch. Refer to 

EC9-390, "Component Inspection (Stop Lamp Switch)"

 (M/T models), 

EC9-

390, "Component Inspection (Brake Pedal Position Switch)"

 (CVT models).

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace stop lamp switch.

Component Inspection (Stop Lamp Switch)

INFOID:0000000010309412

1.

CHECK STOP LAMP SWITCH-1

1.

Turn ignition switch OFF.

2.

Disconnect stop lamp switch harness connector.

3.

Check the continuity between stop lamp switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK STOP LAMP SWITCH-2

1.

Adjust stop lamp switch installation. Refer to 

BR-8, "Inspection and Adjustment"

 (LHD models) or 

BR-52,

"Inspection and Adjustment"

 (RHD models).

2.

Check the continuity between stop lamp switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace stop lamp switch.

Component Inspection (Brake Pedal Position Switch)

INFOID:0000000010929195

1.

CHECK BRAKE PEDAL POSITION SWITCH-1

1.

Turn ignition switch OFF.

+

−

Continuity

Brake pedal position switch

ECM

Connector

Terminal

Connector

Terminal

E30

2

E58

17

Existed

Stop lamp switch

Condition

Continuity

+

-

Terminals

3

 4

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

Stop lamp switch

Condition

Continuity

+

-

Terminals

3

 4

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

BRAKE SWITCH

EC9-391

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

C

D

E

F

G

H

I

J

K

L

M

A

EC9

N

P

O

2.

Disconnect brake pedal position switch harness connector.

3.

Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK BRAKE PEDAL POSITION SWITCH-2

1.

Adjust brake pedal position switch installation. Refer to 

BR-8, "Inspection and Adjustment"

 (LHD models)

or 

BR-52, "Inspection and Adjustment"

 (RHD models).

2.

Check the continuity between brake pedal position switch terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace brake pedal position switch.

Brake pedal position switch

Condition

Continuity

+

-

Terminals

1

 2

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed

Brake pedal position switch

Condition

Continuity

+

-

Terminals

1

 2

Brake pedal

Fully released

Existed

Slightly de-
pressed

Not existed