Nissan Qashqai J11. Manual - part 529

EC9-272

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

P0697 SENSOR POWER SUPPLY

YES

>> GO TO 3.

NO

>> Repair short to ground or short to power in harness or connectors.

3.

CHECK COMPONENTS

Check the following.
• Crankshaft position sensor. Proceed to 

EC9-227, "Component Inspection (Crankshaft Position Sensor)"

.

• Fuel rail pressure sensor. Proceed to 

EC9-209, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace malfunctioning component.

P0833 CPP SWITCH

EC9-273

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

C

D

E

F

G

H

I

J

K

L

M

A

EC9

N

P

O

P0833 CPP SWITCH

DTC Logic

INFOID:0000000010309247

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test. 

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE-1

1.

Turn ignition switch ON.

2.

Fully depress clutch pedal.

3.

Fully release clutch pedal.

4.

Repeat steps 2 and 3 for five times.

5.

Check DTC.

Is DTC detected?

YES

>> Go to 

EC9-274, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM DTC CONFIRMATION PROCEDURE-2

Perform component function check. Refer to 

EC9-273, "Component Function Check"

.

NOTE:
Use component function check to check the overall function of the clutch switch circuit. During this
check, a DTC might not be confirmed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to 

EC9-274, "Diagnosis Procedure"

.

Component Function Check

INFOID:0000000010309248

1.

PERFORM COMPONENT FUNCTION CHECK FOR MALFUNCTION B

1.

Turn ignition switch ON.

2.

Check the voltage between ECM harness connector terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0833

CLUTCH SWITCH SIGNAL 
CONSISTENCY
(Clutch pedal switch “B” cir-
cuit)
• 1.DEF: SIGNAL INCOHER-

ENCE

• 2.DEF: —

Correlation of two clutch pedal position switch signal 
is inconsistency.

• Harness and connectors
• Clutch pedal position switch

ECM

Condition

Voltage

Connector

+

–

Terminal

E58

9

29

Clutch pedal

Fully released

Approx. 0 V

Fully depressed

Battery voltage

EC9-274

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

P0833 CPP SWITCH

NO

>> Proceed to 

EC9-274, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010309249

1.

CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT

1.

Disconnect clutch pedal position switch harness connector.

2.

Check the continuity between clutch pedal position switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair open circuit or short to power in harness or connectors.

2.

CHECK CLUTCH PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1.

Disconnect ECM harness connectors.

2.

Check the continuity between clutch pedal position switch harness connector and ECM harness connec-
tor.

3.

Also check harness for short to ground and short to power. 

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.

CHECK CLUTCH PEDAL POSITION SWITCH

Refer to 

EC9-274, "Component Inspection (Clutch Pedal Position Switch)"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-41, "Intermittent Incident"

.

NO

>> Replace clutch pedal position switch.

Component Inspection (Clutch Pedal Position Switch)

INFOID:0000000010309250

1.

CHECK CLUTCH PEDAL POSITION SWITCH-1

1.

Turn ignition switch OFF.

2.

Disconnect clutch pedal position switch harness connector.

3.

Check the continuity between clutch pedal position switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK CLUTCH PEDAL POSITION SWITCH-2

+

-

Continuity

Clutch pedal position switch

Connector

Terminal

E2

2

Ground

Existed

+

-

Continuity

Clutch pedal position switch

ECM

Connector

Terminal

Connector

Terminal

E2

1

E58

9

Existed

Clutch pedal position switch

Condition

Continuity

+

-

Terminal

1

2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed

P0833 CPP SWITCH

EC9-275

< DTC/CIRCUIT DIAGNOSIS >

[R9M]

C

D

E

F

G

H

I

J

K

L

M

A

EC9

N

P

O

1.

Adjust clutch pedal position switch installation. Refer to 

CL-11, "Inspection"

.

2.

Check the continuity between clutch pedal position switch terminals under the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace clutch pedal position switch.

Clutch pedal position switch

Condition

Continuity

+

-

Terminal

1

2

Clutch pedal

Fully released

Existed

Slightly depressed

Not existed