Nissan Qashqai J11. Manual - part 2167

DAS-82

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

PRE-INSPECTION FOR DIAGNOSIS (CALIBRATING CAMERA IMAGE)

PRE-INSPECTION FOR DIAGNOSIS (CALIBRATING CAMERA IMAGE)

Inspection Procedure

INFOID:0000000010593451

1.

CHECK REAR VIEW CAMERA LENS

Is the rear view camera lens contaminated with foreign materials? 

YES

>> Clean rear view camera lens.

NO

>> GO TO 2.

2.

CHECK REAR VIEW CAMERA INSTALLATION CONDITION

Check rear view camera installation condition (e.g. position, looseness, bent in liftgate lid). 
Is it properly installed?

YES

>> Inspection End.

NO

>> Install rear view camera properly, and perform rear view camera calibration. Refer to 

DAS-101,

"Description"

.

DAS

REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION

DAS-83

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION

Inspection Procedure

INFOID:0000000010416814

1.

CHECK REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION

1.

Start the engine.

2.

Select the “Active Test” item “AIR&WASH ACTIVE” of “AVM” with CONSULT.
NOTE:
Before function check, perform the following items:
• Fill with washer fluid.
• Perform “Active Test” item “WASH ACTIVE” of “AVM” with CONSULT for 4 seconds.

3.

While operating the test item, check the operation.

Is it properly operated?

Washer fluid ejects 4 - 6 times. (Normal function)>>Inspection End.
Washer fluid ejects 7 times or more.>>Properly install or replace air tube.
Washer fluid ejects only once>> Properly install or replace air tube.
Washer fluid does not eject>>Properly install washer tube or replace washer tube and check valve.

DAS-84

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-

TROL UNIT

ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR
CONTROL UNIT

Description

INFOID:0000000010416833

BEFORE REPLACEMENT

When replacing around view monitor control unit, save or print current vehicle specification with CONSULT
configuration before replacement.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing around view monitor control unit.

AFTER REPLACEMENT

CAUTION:

When replacing around view monitor control unit, you must perform “After Replace ECU” with CON-
SULT.
• Complete the procedure of “After Replace ECU” in order.
• If you set incorrect “After Replace ECU”, incidents might occur.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.

Work Procedure

INFOID:0000000010416834

1.

SAVING VEHICLE SPECIFICATION

CONSULT

Enter “Re/Programming, Configuration” and perform “Before Replace ECU” to save or print current vehicle
specification.
NOTE:
If “Before Replace ECU” cannot be used, use the “After Replace ECU” or “Manual Configuration” after replac-
ing around view monitor control unit.

>> GO TO 2.

2.

REPLACE AROUND VIEW MONITOR CONTROL UNIT

Replace around view monitor control unit. Refer to 

AV-267, "Removal and Installation"

.

>> GO TO 3.

3.

WRITING VEHICLE SPECIFICATION

CONSULT

1.

Enter "Re/Programming, Configuration".

2.

If “Before Replace ECU” operation was performed, automatically an "Operation Log Selection" screen will
be displayed. Select the applicable file from the "Saved Data List" and press “Confirm” to write vehicle
specification. Refer to 

DAS-111, "Work Procedure"

.

3.

If “Before Replace ECU” operation was not performed, select "After Replace ECU" or "Manual Configura-
tion" to write vehicle specification. Refer to 

DAS-111, "Work Procedure"

.

>> GO TO 4.

4.

REAR VIEW CAMERA CALIBRATION

Perform rear view camera calibration. Refer to 

DAS-101, "Description"

.

>> GO TO 5.

5.

AROUND VIEW MONITOR CALIBRATION

Perform around view monitor calibration. Refer to 

AV-180, "CALIBRATING CAMERA IMAGE (AROUND VIEW

MONITOR) : Description"

.

DAS

ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-

TROL UNIT

DAS-85

< BASIC INSPECTION >

[DRIVER ASSISTANCE SYSTEM]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

>> GO TO 6.

6.

OPERATION CHECK

Check that the operation of the around view monitor control unit and camera images (fixed guide lines and
predictive course lines) are normal.

>> Work End.