Nissan Qashqai J11. Manual - part 1711

 

  Index      Nissan     Nissan Qashqai J11 - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1709  1710  1711  1712   ..

 

 

Nissan Qashqai J11. Manual - part 1711

 

 

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-145

< SYMPTOM DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000010338834

NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Headlamp (HI) power supply cir-

cuit

• Front combination lamp internal 

circuit

- LED [Headlamp (HI)]
- LED headlamp control module
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-116, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-149, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

Combination meter
Data monitor “HI-BEAM IND”

Headlamp (LO) is not 
turned ON

One side

• Headlamp (LO) power supply cir-

cuit

• Front combination lamp internal 

circuit

- LED [Headlamp (LO)]
- LED headlamp control module
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-117, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-150, "Diagnosis Procedure"

.

Dipped beam indicator lamp is not turned ON
[Headlamp (LO) is turned ON]

Combination meter

Combination meter
Data monitor “DIPPED BEAM IND”

Headlamp (HI) and (LO) is not turned ON

• LED headlamp ground circuit
• Front combination lamp internal 

circuit

- LED headlamp control module
- Harness

LED headlamp
Refer to 

EXL-118, "Diagnosis Proce-

dure"

.

Each lamp is not turned ON/OFF with lighting switch 
AUTO

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-130, "Symptom Table"

.

• Light & rain sensor power supply/

ground/signal circuit

• Light & rain sensor
• BCM

Light & rain sensor
Refer to 

EXL-141, "Component Func-

tion Check"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp internal 

circuit

- LED  (Parking  lamp)
- Control circuit
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-121, "Component Func-

tion Check"

.

EXL-146

< SYMPTOM DIAGNOSIS >

[LED HEADLAMP]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Tail lamp is not turned ON

• Tail lamp power supply/ground 

circuit

• Rear combination lamp internal 

circuit

- LED  (Tail  lamp)
- Harness
• IPDM E/R

Tail lamp circuit
Refer to 

EXL-123, "Component Func-

tion Check"

.

License plate lamp is not turned ON

• License plate lamp power supply/

ground circuit

• License plate lamp bulb
• License plate lamp bulb socket

License plate lamp circuit
Refer to 

EXL-125, "Component Func-

tion Check"

.

Parking lamp, license plate lamp and tail lamp are not 
turned ON

Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to 

EXL-151, "Diagnosis Procedure"

.

Position lamp indicator is not turned ON
(Parking lamp, license plate lamp and tail lamp are 
turned ON)

Combination meter

Combination meter
Data monitor “LIGHT IND”

Daytime running light is not turned ON

• Daytime running light power sup-

ply/ground circuit

• Front combination lamp internal 

circuit

- LED (Daytime running light)
- Control circuit
- Harness
• IPDM E/R

Daytime running light circuit
Refer to 

EXL-126, "Component Func-

tion Check"

.

Turn signal lamp does not 
blink

Indicator lamp is normal
(All of turn signal lamp is 
not blinks)

• Fuse
• BCM power supply (turn signal 

lamp) circuit

• BCM

Turn signal lamp circuit
Refer to 

EXL-136, "Component Func-

tion Check"

.

Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)

• Front turn signal lamp
- Front turn signal lamp power sup-

ply/ground circuit

- Front turn signal lamp bulb
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-

ply/ground circuit

- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-

ply/ground circuit

- Rear turn signal lamp bulb
- Rear turn signal lamp bulb socket
- BCM

Indicator lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-130, "Symptom Table"

.

Turn signal indicator lamp 
does not blink
(Turn signal lamp is normal)

One side

Combination meter

Both sides
(Always)

• Turn indicator signal
• BCM
• Combination meter

Combination meter 
Data monitor “TURN IND”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch OFF)

• Combination meter power supply/

ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-61, "COMBINATION 

METER : Diagnosis Procedure"

.

Symptom

Possible cause

Inspection item

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-147

< SYMPTOM DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

• Hazard warning lamp does not activate

(Turn signal is normal)

• Hazard warning lamp continues activating

• Hazard switch signal/ground cir-

cuit

• Hazard switch
• BCM

Hazard switch
Refer to 

EXL-143, "Component Func-

tion Check"

.

Stop lamp and high-mount-
ed stop lamp are not turned 
ON

All of stop lamp and high-
mounted stop lamp are 
not turned ON

• Fuse
• BCM power supply (stop lamp) 

circuit

• Stop lamp switch power supply/

signal circuit

• Stop lamp switch
• BCM

Stop lamp circuit
Refer to 

EXL-128, "Component Func-

tion Check"

.

Any of stop lamp and 
high-mounted stop lamp 
are not turned ON

• Stop  lamp
- Stop lamp power supply/ground 

circuit

- Rear combination lamp internal 

circuit

• LED (Stop lamp)
• Harness
- BCM
• High-mounted stop lamp
- High-mounted stop lamp power 

supply/ground circuit

- High-mounted stop lamp
- BCM

Front fog lamp is not turned 
ON

One side

• Front fog lamp power supply/

ground circuit

• Front fog lamp bulb
• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-132, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-152, "Diagnosis Procedure"

.

Front fog lamp indicator lamp is not turned ON
(Front fog lamp is turned ON)

Combination meter

• Combination meter

Data monitor “FR FOG IND”

• BCM (HEAD LAMP)

Active test “FR FOG LAMP”

Rear fog lamp is not turned 
ON

Rear fog lamp indicator 
lamp is normal

• Rear fog lamp power supply/

ground circuit

• Rear fog lamp bulb
• Rear fog lamp bulb socket
• BCM

Rear fog lamp circuit
Refer to 

EXL-134, "Component Func-

tion Check"

.

Rear fog lamp indicator 
lamp is included

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-130, "Symptom Table"

.

Rear fog lamp indicator lamp is not turned ON
(Rear fog lamp is turned ON)

• Rear fog lamp status signal
• BCM
• Combination meter

• Combination meter 

Data monitor “RR FOG IND”

• BCM (HEAD LAMP)

Active test “RR FOG LAMP”

Headlamp auto aiming does not activate

• Fuse
• Headlamp aiming motor power 

supply/ground circuit

• Headlamp aiming motor
• IPDM E/R

Headlamp levelizer circuit
Refer to 

EXL-119, "Component Func-

tion Check"

.

Symptom

Possible cause

Inspection item

EXL-148

< SYMPTOM DIAGNOSIS >

[LED HEADLAMP]

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000010338835

LED HEADLAMP

• LED brightness and color may slightly change until the temperature becomes stable. This is not malfunction.
• Illumination time lag may occur between right and left. This is not malfunction.
• Brightness may be reduced due to aged deterioration of LED.

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes for the control difference. This
is normal.

HIGH BEAM ASSIST SYSTEM

When driving while using the high beam assist system, the headlamp beam may not switch or the beam
switching timing may vary according to the ambient environment (the condition of the vehicle ahead, the con-
dition of the road, the position of the vehicle, etc.).This is due to control differences and is not a malfunction.

 

 

 

 

 

 

 

Content   ..  1709  1710  1711  1712   ..