Nissan Qashqai J11. Manual - part 1706

LICENSE PLATE LAMP CIRCUIT

EXL-125

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

LICENSE PLATE LAMP CIRCUIT

Component Function Check

INFOID:0000000010338812

1.

CHECK TAIL LAMP LH OPERATION

Check that tail lamp LH is turned ON when lighting switch is turned 1ST.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check tail lamp circuit. Refer to 

EXL-123, "Component Function Check"

.

2.

CHECK LICENSE PLATE LAMP OPERATION

With CONSULT

1.

Select “TAIL LAMP” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the license plate lamp is turned ON.

Is the inspection result normal?

YES

>> License plate lamp circuit is normal.

NO

>> Refer to 

EXL-125, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010338813

1.

CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector and license plate lamp connector.

3.

Check continuity between IPDM E/R harness connector and license plate lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK LICENSE PLATE LAMP GROUND CIRCUIT

Check continuity between license plate lamp harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK LICENSE PLATE LAMP BULB

Check the applicable license plate lamp bulb.
Is the inspection result normal?

YES

>> Check the corresponding license plate lamp bulb socket. Repair or replace if necessary.

NO

>> Replace the corresponding license plate lamp bulb. Refer to 

EXL-178, "Replacement"

.

On

: License plate lamp ON

Off

: License plate lamp OFF

IPDM E/R

License plate lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E37

4

D97

1

Existed

LH

D96

License plate lamp

—

Continuity

Connector

Terminal

RH

D97

2

Ground

Existed

LH

D96

EXL-126

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

DAYTIME RUNNING LIGHT CIRCUIT

DAYTIME RUNNING LIGHT CIRCUIT

Component Function Check

INFOID:0000000010338814

1.

CHECK DAYTIME RUNNING LIGHT OPERATION

With CONSULT

1.

Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.

2.

With operating the test items, check that the daytime running light is turned ON.

Is the inspection result normal?

YES

>> Daytime running light circuit is normal.

NO

>> Refer to 

EXL-126, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010338815

1.

CHECK DAYTIME RUNNING LIGHT OUTPUT VOLTAGE

With CONSULT

1.

Turn ignition switch OFF.

2.

Disconnect front combination lamp connector.

3.

Turn ignition switch ON.

4.

Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.

5.

With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace IPDM E/R. Refer to 

PCS-67, "Removal and Installation"

.

2.

CHECK DAYTIME RUNNING LIGHT POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and front combination lamp harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT

Check continuity between front combination lamp harness connector and ground.

On

: Daytime running light ON

Off

: Daytime running light OFF

+

-

Test item

Voltage

IPDM E/R

Connector

Terminal

RH

E101

50

Ground

DAYTIME RUN-
NING LIGHT

On

9 – 16 V

Off

0 – 1 V

LH

E102

57

On

9 – 16 V

Off

0 – 1 V

IPDM E/R

Front combination lamp

Continuity

Connector

Terminal

Connector

Terminal

RH

E101

50

E93

4

Existed

LH

E102

57

E91

DAYTIME RUNNING LIGHT CIRCUIT

EXL-127

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Is the inspection result normal?

YES

>> Replace the corresponding front combination lamp. Refer to 

EXL-161, "Removal and Installation"

.

NO

>> Repair or replace harness.

Front combination lamp

—

Continuity

Connector

Terminal

RH

E93

6

Ground

Existed

LH

E91

EXL-128

< DTC/CIRCUIT DIAGNOSIS >

[LED HEADLAMP]

STOP LAMP CIRCUIT

STOP LAMP CIRCUIT

Component Function Check

INFOID:0000000010338817

1.

CHECK STOP LAMP OPERATION

1.

Turn ignition switch ON.

2.

With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON.

Is the inspection result normal?

YES

>> Stop lamp circuit is normal.

NO

>> Refer to 

EXL-128, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010338818

1.

CHECK SYMPTOM

Check symptom (A or B)

Which symptom is detected?

A

>> GO  TO  2.

B

>> GO  TO  7.

2.

CHECK FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.

3.

CHECK BCM POWER SUPPLY (STOP LAMP)

1.

Disconnect BCM connector.

2.

Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK STOP LAMP SWITCH POWER SUPPLY

1.

Disconnect stop lamp switch connector.

Depressed

: Stop lamp and high-mounted stop lamp 
ON

Fully re-
leased

: Stop lamp and high-mounted stop lamp 
OFF

Symptom

A

All of stop lamp and high-mounted stop lamp are not turned ON

B

Any of stop lamp and high-mounted stop lamp are not turned ON

Unit

Location

Fuse No.

Capacity

• BCM
• Stop lamp switch

Fuse block (J/B)

#24

10 A

+

-

Voltage

BCM

Connector

Terminal

M68

145

Ground

9 – 16 V